Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
we were trying to retrieve some raw data from the REST API from a WLC from a PI instance , however we are not getting any output, sample query and response as below: H:\>curl -k "https://avcapi:Qwerty123@10.150.98.17/webacs/api/v4/op/statisticsS...
Resolved! Cisco WLC Anchor WLANS Limit
Dear All, I planning to configure a new Cisco WLC 5520 as anchor controller.The foregin controller is already in place and it is a WLC 5508.I 'd like to use the Anchor WLC fot the Guest WLAN, but also I need to use it for other ten WLANS. Are there s...
Hi all Im trying to find out how often Prime will sync data to DNA-C when setting up automatic sync in the Co-excistence tool.I cant quite seem to find that info anywhere. But for example, if I move an AP on a map in Prime, how much time will pass un...
Hi,I have some 3602i APs with the AC module and I am looking to push 20W out of their ports for enhanced POE, but it would appear that the WS-C3750E-48PD-SF we have (Motherboard revision number : B0) will only allow up to 15.4W.Any idea what other se...
Dear All,does anyone know what this Error in Cisco Prime means ? It had been reported for 2 of our controllers right at the same time. But none of the controllers was having an issues at that time. According to the Syslog and DNA Center.Thanks,Thorst...
Resolved! FlexConnect L3 Roaming
Hi Folks, I know this has been answered but seems to be a good few years now. I also can't find any supporting documentation to say otherwise. IntraWLC Roaming on FlexConnect SSID. If you roam between APs that have different VLANs configured for the ...
Hi ..configured CIMC Port on WLC 5520.set admin password on cli(WLC5520) >imm username admin password test123 test123(WLC5520) >imm summaryThis will take some time...Please be patient!User ID.......................................... adminDHCP..........
For the life of me, I cannot get the configuration for repeater ap and root ap to work. My configuration is simple. It's just 2 APs and no Cisco switches involved and therefore no vlan is involved. It's just 2 aps and 1 ssid on DotRadio 1. I tried ...
Hello, I configured my 1832 APs with 8.10.122 release Mobility Express.My computer just close to the AP shows a data rate of 86,7 Mbps.With my home zyxell, same place, same channel, same computer I have a data rate of 433,3Mbps.Any idea?
Hi guys,1140 APs don't register with the 5508 controller. Here are some debug outputs:AP's IP: 100.31WLC's IP:100.2debug capwap events enable*spamApTask1: Nov 01 11:25:04.958: 30:e4:db:d3:a4:ca Discovery Request from 192.168.100.31:47690 *spamApTask1...
Hi, At what interval Prime Polls the wireless controller to get the wireless clients ? In the User Guide, I see it is mentioned as "Wireless clients are discovered from managed controllers or autonomous access points. The controllers are polled duri...
Hi all,I'm not sure about the settings of the"Antenna Configuration" for an 1852E Mobility Express Access Point. If I look at the datasheet for the 1852E, it notes that 2.4GHz uses 3 antennas. -> Does that mean that for Radio 1 only 3 Antennas need t...
Hi, Can we disable SSL2.0 TLS1.0 in Cisco Prime infrastructure ? If so, how ? I found the command to enable it, but not disable it.
Gents,Is it possible to disable workstation-to-workstation communication in a wireless network using Cisco ISE ?. I know it can be done in the wired network using dynamic ACLs. Regards,Edouard.
Dear All,One Access Point (2802i) has been joined to the controller already and working fine. But when I try to join other AP to the same controller it is not joining. WLC-9800 IOS : 16.12.1
