Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Good dayI would like to ask a question.Can an AP be recovered from one management account and transferred to another?I work in a school and the network administrator who worked here before me, did not provide the access information of the APs and now...
Hi wireless professionals,in the C9800 GUI, there are radio statistics for each radio. The details of a radio shows the "Coverage Information", which tells whether the "Coverage Profile" or "Interference Profile" is "Passed" or "Failed".There are sta...
We upgraded the firmware on our 3504 to 8.10.151.0. The aps we are using are 2802's. We are getting errors in the logs stating that the ap's are not reachable to wsa server. How can I make it so they stop trying to connect? Below is a few lines of ...
We have 3 large sites, WLC5520 and 8510s all running 8.5.171.0We have a Foreign/Anchor with external Company, the link for this comes to site 1.Their WLC is a 5508 running 8.5.151All 3 sites and WLCs anchor back to this 5508.I'm getting intermittent ...
Hi Team,I have been experiencing a DHCP lease problem where a number of users who connect to an SSID receive an invalid subnet lease (or wrong DHCP allocation), whilst other users can connect to the same SSID and receive a valid IP address assignment...
Hi everyone, I'm having a strange issue when setting up a 9800 EWC on a C9115.When powering the EWC up and making the initial configuration through the CLI (putting IP, mask, gateway, ...) and saving it, I can't access the management interface.The po...
Hello everyone, I'm trying to configure a Cisco Catalyst 9130AX but I'm running into this error when I validate the configuration. Any idea of what I can try to solve this? Thanks.AP216>wireless config validate AP216>*Sep 15 09:53:34.769: %SYS-5-CONF...
Resolved! aWIPS and Rogue Detection
Hello community, Now I'm deploying aWIPS and Rogue detection with the DNAC, and I have some access points in flexconnect mode to serve clients and some other APs in monitor mode to detect rogue, threats....When I go to rogue and aWIPS dashboard I fin...
Resolved! Changing Authentication to WPA2
HelloWe want to change the encryption mode to WPA2 which is currently setup as WPA1 and WPA2. My question is what will be the impact of this on end users. We have lot of devices in the network and i am concerned that changing the encryption method wi...
Difference in cat M1 and Cat 1 devices ? Is CAT m1 devices work in areas where CAT 1 devices work.? Is there any special antenna requirements for CATM1 devices ? could you please answer above questions ASAP. We need to take decision to buy modems as ...
Resolved! Cisco Aironet 2802E
We recently bought a Cisco Aironet 2802E and I was wondering if there is a way to convert this access point into a Standalone (Autonomous) access point. Currently, the image is mobility express and I can't seem to find any instructions to go from mo...
Hello community, I have an issue with adding APs to Cisco DNAC floor map, When I click edit>>add APs I can't find the list of APs associated with this floor, I want to know if the APs should be provisionned or just discovered by the DNAC.Thank you fo...
Hi, Having some problems getting the correct CAPWAP-header DSCP-markings for Teams-traffic in the upstream direction. I see that the clients are WMM-enabled, and that the DSCP-value in the original header is correct. However, this value is not transf...
hello, I deploy a new cisco 9800-CL VMware vm and attache some AP 9117AXI to it. I configure some stuff in central switching mode to have the wifi deploy. I test bandwith between AP vlan and the Controleur vlan with iperf and obtain around 800 Mbit/s...
HelloI have a Fortigate Firewall 200E with 6 Forti access points. My APs have a corporate SSID (10.0.0.x and access to corporate resources) and a guest SSID (10.0.1.x with no access to company resources). I did not setup VLANs on my firewall so I thi...
