Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! Separate Networks in one bldg
Hi there,I've come across a situation where a portion of a bldg (and network) will be used by a separate sub-entity. There will be no network changes (same internet egress, same dhcp setup, etc) other than not wanting entity B's local tech having acc...
I edit web bundle, and i whant download files to wlc. But when i try do this throw Web-gui i got alert : 'Download operation failed. Please check connectivity to the server.' So, i have a TFTPD64 running in remote PC (172.16.12.35) (but in one networ...
Resolved! AP does not join WLC.
Hi. AP does not join WLC.The AP tries to join the WLC, but the session does not appear to be established.Attach debug content. May 11 08:13:09 kernel: [*05/11/2021 08:13:09.8076] CAPWAP State: DiscoveryMay 11 08:13:09 kernel: [*05/11/2021 08:13:09.8...
Resolved! Catalyst 9120 AP with only .af power
Hello community, can anyone give me a hint on how to disable the LED continuously cycling through red-green-blue while a 9120 AP is powered with only 15.4w? Is that possible at all? Robin
In Active Directory we have Complex Password requirements enabled. We want to setup an SSID for our Printers use MAC authentication with Radius using NPS. We can use the MAC addresses to create the users, but we are unable to set the Password to the ...
Resolved! Kick clients off an SSID
Hi,I'd like to kick multiple clients off an SSID. I know I can block them permanently under Network-wide > Clients, but I'd like to just kick them out so that they can connect again if they want to.
On the controller under "Inventory" the "Maximum number of APs supported is set to 0 (zero). Attempts to set the max number to 200 or any number for that matter via the CLI has failed. The setup has been running for about 3-4 years now. Checks on the...
Does anyone know if it's possible to set a device rate limit (downstream/upstream) via the RADIUS Access-Accept response like we can in AireOS using similar to the below attributes:Airespace-Data-Bandwidth-Average-ContractAirespace-Data-Bandwidth-Bur...
I keep getting a https error NET::ERR_CERT_COMMON_NAME_INVALIDwhile trying to use externally generated certificate Windows server 2019 Default webserver Template Did I do something wrong?Error is on all browsers
Hi,Our customer has a network consisting of 9800 (IOS XE) WLCs, 9130 APs and ISE 2.6p6.They want to provide a free guest wifi solution with a very low basic bandwidth of say 1Mbps. This will be on a dedicated SSID (Guest_Free_Wifi)They also want to p...
hi, currently we have 9800 vwlc integrated with ISE. the requirement is that when mobile connects to SSID ((flexconnect SSID with Layer2 WPA2 and 802.1x), it can access only internet and should connect to internal resources except for dns and dhcp pu...
Resolved! FlexConnect in a local network
Hello, I have basic knowledge of FlexConnect and when it's used - branch offices and remote sites. Recently I've been told by some auditors that we should configure FlexConnect in our local network to increase wireless speed and quality. I've never h...
What is the default username and password for cisco ironport web security appliance?
Hi What is relation between radio mac and ethernet mac? Can we know ap ethernet mac address from its radio mac? Thank you
Resolved! Voice Vlan tag on Meraki MR33
HiI have 30xMR33 in my warehouse all of them are setup with a SSID using radius. This SSID is used for Data only and is on the native VLAN (vlan 1). I have added and setup a new SSID for Voice only I would like the additional SSID use the VLAN 2 for ...
