Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi, I have issue with the wireless users are not getting IP address from the IOS DHCP server.But, after ipconfig /renew the wireless users get IP address. LAN user can get IP Address without problem.the setup of the network is straight forward WLC-->...
Hi all, please, could you kindly help me? We need to configure APs 2802 for GUINEA ECUATORIAL. In the Wireless LAN Compliance Lookup, this country does not appear. Is there anyone who knows if it is -E or another? Thanks a lot
Hello,I want to know the power consumption of cisco WLC 9800-40 but I can't find this information in the device datasheet.Thank you for your support. Best regards
Hello,I have a Spectralink 8440 connected to a C9800-CL 17.3.3 in Flexconnect mode Local Switching.According to the Spectralink VIEW Guide this is currently not supported, however I currently have no other option.The only problem I am currently exper...
Hi Guys, We are facing user disconnections and slow speed issue on one of our site. We are moving from Aruba 7210 controllers to Cisco C9800 (WIFI 6). We have removed half of our Aruba APs and installed Cisco APs (9120ax). Currently both the controll...
Hello, I have a couple of APs 2802i, I'm using them to do a Site Survey APoS, both are configured exactly the same, as well they have the same version, the problem is that one of them is broadcasting with much lower power than the other (both are con...
At one of our sites we have 3 8540's. Two are in an HA SSO paring with the 3rd in N+1. I need to upgrade the OS on all three. What is the best procedure to do this. Should I upgrade the Paring first then N+1 WLC. The goal of course doing it with the ...
Hi there,I've come across a situation where a portion of a bldg (and network) will be used by a separate sub-entity. There will be no network changes (same internet egress, same dhcp setup, etc) other than not wanting entity B's local tech having acc...
I edit web bundle, and i whant download files to wlc. But when i try do this throw Web-gui i got alert : 'Download operation failed. Please check connectivity to the server.' So, i have a TFTPD64 running in remote PC (172.16.12.35) (but in one networ...
Hi. AP does not join WLC.The AP tries to join the WLC, but the session does not appear to be established.Attach debug content. May 11 08:13:09 kernel: [*05/11/2021 08:13:09.8076] CAPWAP State: DiscoveryMay 11 08:13:09 kernel: [*05/11/2021 08:13:09.8...
Hello community, can anyone give me a hint on how to disable the LED continuously cycling through red-green-blue while a 9120 AP is powered with only 15.4w? Is that possible at all? Robin
In Active Directory we have Complex Password requirements enabled. We want to setup an SSID for our Printers use MAC authentication with Radius using NPS. We can use the MAC addresses to create the users, but we are unable to set the Password to the ...
Hi,I'd like to kick multiple clients off an SSID. I know I can block them permanently under Network-wide > Clients, but I'd like to just kick them out so that they can connect again if they want to.
On the controller under "Inventory" the "Maximum number of APs supported is set to 0 (zero). Attempts to set the max number to 200 or any number for that matter via the CLI has failed. The setup has been running for about 3-4 years now. Checks on the...
Does anyone know if it's possible to set a device rate limit (downstream/upstream) via the RADIUS Access-Accept response like we can in AireOS using similar to the below attributes:Airespace-Data-Bandwidth-Average-ContractAirespace-Data-Bandwidth-Bur...
