Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi All, Please clarify the points and help me to understand the following. I am planning to add few more WiFi monitoring in place and looking for your suggestion on this item. Thank you.. 1)CleanAir Sensor down:- Can someone explain me what is the im...
I'm receiving a lot of events with the message "Radius server X.X.X.X port (1813) is deactivated". The problem I'm facing is that I cant find any config releated to that spesific radius server on the WLC that reports the event.. I ran show run-config...
Resolved! Converged access migration to AireOS
Is there any recommended method how to move APs from Cat3850 converged access controller to existing AireOS WLC?How can I make the APs to perform a standard discovery process with DHCP Opt 43 and not to join to the CA mobility controller?Some APs are...
Resolved! Tune/tweak Rogue AP settings on AireOS
Hi,I receive a lot of alarms related to rogue AP's. Haven't done much tweaking om Rogue AP settings on the WLC.Does anyone have recommendations for what settings I should use?
Hi,I'm trying to connect an internal server on my LAN but in another subnet.The wireless clients get their addresses in the 192.168.35.0/24 subnet.The addresses are correctly distributed by a DHCP pool on my firewall.Unfortunately no wireless client ...
In the "Aministration> management" of the WEBUI of C9110 AP EWC, the backup & restore option cannot be found. Does it mean that the EWC can only back up the configuration in the CLI through "copy startup-config tftp:"?
Hi Hope you all are great! i have been reading specs for both model i.e AIR-CAP3602I-A-K9 & AIR-CAP2602I-A-K9 but having little confusion here can u please share knowledge with me that what's the dbi of both APs where i have read that 2602I has 4 d...
I want to know whether we can deployment one 5GHz for one SSID? Are the functions mentioned below implemented now? If it can be achieved, does anyone know how to deploy? Thank you i have read the cisco doc on Release 8.3Currently both Macro (green) a...
Resolved! ACL for Internet only
I want to deny the internal network (172.16.0.0 ~ 172.32.0.0) and permit only the Internet.Is there a problem with my ACL? 172.27.144.0 : Wireless172.30.1.61 : DHCP172.30.1.15 : DNS172.25.1.201,208 : Fileserver Thank you.
Hi , My WLC is 5520 firmware on version 8.10.x , All APs are .ac wave2 and "FlexConnection Mode" I have an issue, When using the voice application such as Skype,MS Team etc. Sometimes voice not stable-The internet source no any QoS- client sn...
Resolved! Broadcast does not pass WLC 2504
Good day.I can’t configure Sonos via WIFI network. Built on CIsco WLC 2504.Attachment Scheme.When setting up, you need to press the buttons on Sonos and it starts sending broadcast pacet to the network at the address 255.255.255.255. which the phone ...
Resolved! Adding WAP to network w/o any.
I want to add a Meraki WAP to my network. It is the only WAP and will be behind firewall. I have a small wireless router behind the firewall but it does not cover the area I need. What is the simplest way to add it. I have POE cat6 to the location, a...
Hi All, Sorry in advance if this comes across as a dumb question. Background - Currently have a 2702 model AP connected to a 2960 switch in a large warehouse setting. We want to add two more WAPs in the area. Due to the location it is not easy to run...
Hello! So with help I got my "root" AP set up and working perfectly fine with 2 SSID's; House0fM vlan 10 and House0fMVPN vlan 11 and whichever SSID I connect to, goes to that vlan through the Catalyst Switch the AP is connected to, and works fine.The...
Hello, All wireless barcode canner stop working because its time issue so that we cannot login. We tried many ways to resolve the issue, but failed. The last way is to check time system on AP and WLC. We can see their time and day are correct. Please...
