Team,I have an AP 2702i that was factory reset and when I connect it to vWLC 8.5.161.0 it cannot register. Attached logg of the AP, has anyone seen this error ?. AP500f.8094.85a0#*Aug 19 19:19:37.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Ale...
Hello,I recently upgraded my 1830 AP to version 8.10.130.0. After completing, I am experiencing the following:1. LED indicator changes Green->Red->Amber repeatedly2. No access points are listed in the Access Points table in Wireless Settings. And...
Hey all We recently purchased a Aironet AP1852I-E-K9 unit to use as a stand-alone WAP extension for an existing wired network. All it had to do was add wireless tablets to our existing wired network. There are no other wireless devices, no wireless c...
Hi Team, I wanted to know, do I need to procure 2xAP adder license if I am running virtual WLC as Primary and Secondary in same mobility group. i.e 1 adder license for each vWLC.
Hi, i have the following issues on a cisco air ap 2802I-E-K9e choose one of the following boardsand starts over and over again Please choose one of the following boards:1. 3K2. 2K (new)3. 2K (proto)4. Milos5. 2KH6. 3KVE (v-sku)7. 3KH/3KA/4K8. Duploi...
I have some older computers/consoles. That do not have good wifi, or the wifi is not workingI have my home network which is wifi because I am unable to wire the house for ethernet for a few reasons. The Ethernet does not reach the location for the ol...
Dear all, Currently I used Aironet 1850 as master wlc using Mobility Express, (firmware 8.10.121.0). We are running on global password right now but plan to change it into unique ID per user via authentication via Active Directory, the configuration...
Good day, fellow techies, This is a new one to me. I have a 5508 WLC which I'm attempting to do a factory reset on. I can get into the boot menu OK, but when I select option '4' to 'Clear Configuration,' the unit says 'Launching,' waits a few seconds...
Is there a validated design for Meraki wireless capable of being utilized as a Point to Point bridge to back haul all traffic from a secondary building to a main building with L3 Switches instead of MX devices?The use case would be for Wired and Wire...
Hi, I am using a Cisco any connect secure mobility client vpn. Currently my office location is in bengaluru, INDIA. However, due to current pandemic situation I want to relocate to my hometown kolkata and work from my home location. Will my VPN be co...
Hi Experts, User is able to log in when enter 1.1.1.1 address manually. It works in chrome and firefox but not in safari. Usually when user connect to the guest wifi request will go to the DNS server and automatically redirect to the controller page ...
Hello we will test the throughput of an access point and we have two phones (Glaxay A10 and Hawuei) the problem: why if we are in the same position to test the throughput ( speed test via phone ) , the two phones ( (Glaxay A10 and Hawuei) give dif...
I configured a Virtual WLC using VMware which is connected to a Nexus5K via Trunk. Show CDP displays the information about the vWLC and I also created a L3 interface on the N5K from where I can ping DGW and another WLC (5508 appliance) in the same VL...
I have customer reports related to wireless access disconection. By enabling a debug on de WLC we catched the following information ( see attachment)In addition, WLC is recording the following message Wed Aug 19 14:41:47 2020--Client Authenticated: ...
I have a Cisco 3802E running 8.2.151.0 I wan to upgrade it to AIR-AP3800-K9-ME-8-10-130-0. AP Running Image : 8.2.151.0Primary Boot Image : 8.2.151.0Backup Boot Image : 0.0.0.01 Multigigabit Ethernet interfaces1 Gigabit Ethernet interfaces2 802.11 R...
