Hi Guys I need to know can we use Cisco AP as a RFID Scanner? If it can use as a RFID Scanner, then please mention what AP models and IOS versions can use for that. Many Thanks. Regards Oshaka
Forum Posts
Hello, FRA is globally disabled on our 5520 WLC (8.2.130 code) On the other hand when we look at the APs list on 802.11b/g/n tab, we can see only for 3802I or E : or For other AP models, like 3702 or 2702 we have : Could you tell me why the ...
I need to deploy an WPA3 enviroment for one of my custumers. i'm using a 1852 AP witch the last firmware.There will be an upgrade version that support wpa3?
Hi. I'm trying to research the following command: debug dot11 d1 dfs simulate Does anyone know if simulates a DFS event on an AP or does it more "emulate" a radar and send out a little RF pulse from an AP to neighbouring APs? I'm looking for a way t...
Resolved! WLC Load Profile Failure
Hi AllAny ideas on the issue below would be much appreciated: 5508 WLC v7.6 code, with 4x 3702i AP's attached, 10>15 Wireless clients average on x2 of the AP's (the Cisco stats say these AP's should handle 128 clients if pushed to their max), the oth...
Resolved! Virtual WLC certificate problem
A problem occurs when trying to install a WebAuth certificate: TransferTask: Sep 19 10:04:47.389: Adding cert (7998 bytes) with certificate key password. *TransferTask: Sep 19 10:04:47.389: Add WebAuth Cert: Adding certificate & private key using pas...
Hi, for HA SSO following topology is being used: Core 1 is primary for spanning tree and HSRP VLANs used for SSIDs offered by WLC1(primary) & WLC2(stanby). WLC1 & WLC2 configured in HA SSO mode and connected via etherchannel to core switches. ...
Hi, I am planning an update to our WLC and AP's (2602s) and wanted to clarify the behaviour around the pre download function. We are going from 8.0.152.0 to 8.3.143.0 I know from both the GUI and CLI you can issue a command to pre download soft...
Hi, I'm replacing an existing network of autonomous APs with Cisco Mobility Express (v 8.7) using 2802i APs. We use a total of 3 BSSIDs on this network. For business reasons, we want certain APs to only include a single WLAN BSSID. Via the Mobi...
Resolved! joint AP to wireless controller 2504
hello all,I am new in wireless , i have Cisco wireless controller 2504 for 50 access point, access point 1262 and switch 3560.i setup the controller correctly and i contect it to the switch and connect the AP to the switch.i can ping from the AP to ...
I have a warehouse with 3700 AP's all using only 5GHz with 2.4GHz disabled. In the warehouse we use both the MC3190 and MC32N0 scanners. I am getting a lot of complaints about network issues by users of the MC3190 scanners. When I run link tests t...
We tried to take backup of Cisco prime for one of our end client using remote repository. But the problem is now the backup size is 43gb and the ftp server size is only 17gb. So it failed. Is there any other way to take backup apart from defaultRepo?...
Hi, we are planning to migrate our wireless solution from cloud based solution (Cisco Meraki) to avoid yearly recurring subscription expense. currently Meraki APs (total- 75 qty) are working at HQ and Branches (10 offices). all branches are connected...
For quite some time, performance on the office extend solution for our internal end users has been exceptionally poor, basically unusable to be accurate. However VPN connectivity via AnyConnect or an IPSEC VPN client was fast.I do know the solution u...
Hi, We have a Cisco , and the customer want to have 3 WLAN, but he want to have one captive portal for each WLAN, only have the WLC he don´t have some external server, it is possible to have three different captive portals in WLC locally? Thanks.
