Hi,We inserted NC6-60X10GE-M card in NCS; it appears in admin mode but doesn't appear in XR mode. I have attached the logs. Please advise.Best regards!
Hello I have a problem for the VSM on the ASR9K1.in the version of the 5.1.3 ,If I want to do the NAT44 in the projecthow many inside vrf (sourc) and outside vrf(destination) I can have on the one VSM card?2.Now i'm in the 4.2.2 , i need to update in...
Hi all,after booting platform ASR9010 there are some log messages like this:LC/0/1/CPU0:Feb 26 09:00:17.912 : ssm_process[325]: %OS-SSM-6-NODAL_SERVICE_STATE_CHANGE : Nodal service state changes from AVAILABLE to UNAVAILABLELC/0/0/CPU0:Feb 26 09:00:1...
HiEveryone I have a doubt about the configuration for the helper address on ASR9000, mainly I try to configure the helper address in this way: configureinterface type numberipv4 helper-address vrf vrf_name address However it doesnt work.What is the ...
Asking all our customers. Looking for some other examples where we had an issues on the a9k where we might have some gap in system resiliency. Looking for issues where we might have seen a HW or SW issue and the router didn't handle it in a way yo...
HiHave anyone encountered such behavior?We are importing routes from vrf SGI1 to vrf C3. Both vrf's are situated on one device (ASR-3). Traffic is going in direction from the Internet to the vrf C3, then jumps to vrf SGI1 and goes to another equipmen...
Hi All,we are planning to setup OAM for monitoring performance of our VPLS service interface? By checked Cisco document, I couldn't find related document that can confirm Y.1731 support multi-point to mulit-point interface by full mesh topology in o...
What is the number of full rate (128pps) PTP client slaves supported on ASR9k platform configured with RSP 440 and working as boundary clock? Platform has MOD80-SE and MPA-4x10G LCs.Thank you,Danijel
I´m installing a XFP-10G-MM-SR on a CRS-FP140 card. However, according to the XFP Compatibility Matrix on CRS, this Version and type of module is not supported. The problem is that we don´t know the version of the XFP when we are in the purchasing pr...
Hi All,I have a problem in CRS 8/S 400G: I have a 40X10GE-WLO Line Card on Slot 0 but it is not powered on and not shown in "show inventory" CLI command output. I tried to put this card in other slot but I had the same problemYou will find in attache...
Hi XR folks, I enabled this feature on XR 4.3.2 as following configuration,logging archive device harddisk severity notifications file-size 5 frequency daily archive-size 100 archive-length 4 The issue is,There have no Archiving logging file be gener...
Hi SP Folk,BackgroundI need to provide L3 termination for CE device.CE device on the production having no vlan tagging capability.Scenario. (See also attachment , diagram)There are ASR9K and ASR903 connected together,running VPLS as followingASR9K co...
HiI have two ASR9k with ISM modules running the CGN NAT serviceI have configured two /21 pools on each box , which means 4096 IP address for each box , when I check the statisticsRP/0/RSP0/CPU0:CGN-3G-NAT1#show cgn nat44 nat1 statisticsStatistics sum...
Hello,We followed this thread´s advice (https://supportforums.cisco.com/message/3753984) to get a CGN up and running with a single vrf instance (IOS XR 4.2)Everything seems to be ok but we are getting the following error:asr#show cgn nat44 NAT444 sta...
In a month the second case all are disconnected Rrroyesessii and new aren't connected not to reboot a router yet.Messages RP/0/RSP0/CPU0:Feb 12 20:17:00.396 : pppoe_ma[378]: Bundle-Ether100.10: I dst ffff.ffff.ffff src bcee.7bed.90a0: len 46 0x110900...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: