Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1999465members
1359892discussions

Community Activity

ikev2 profile certificate map problem

I am trying to make two different ikev2 profiles for two different group of users. I am trying to distinguish between them based on the serial number of certificate. However any certificate that is issued by the CA always fall under the first profile...

HermanAkv by Level 1
  • 550 Views
  • 20 replies
  • 0 Helpful votes

device profiling on WLC 9800 running IOS-XE

Hey everyone,Is there a way to update the OUI database in the WLC running IOS-XE.  I think there was a way with AirOS, but I don't see it in IOS-XEWhat I want to do us upload the updated OUI database from https://standards-oui.ieee.org/oui/oui.txt so...

Alex-Pr by Level 1
  • 76 Views
  • 3 replies
  • 0 Helpful votes

Calling Name being stripped from SIP headers

Hello, I have a customer with CUCM 14SU1. They have recently purchased a VG410 which has 48 FXS ports which connect analog phones at one of their sites. The VG410 is not supported as an SCCP gateway until CUCM 14SU3 so I have set it up with dial peer...

Resolved! Split Traffic between 2 Firewall from my Core Switch C3850

The goal i want to achieve here based on from the diagram below:i want user1 - 192.168.20.x to pass FG-FW01 192.168.1.1i want user 2 -192.168.50.x to pass FG-FW02 192.168.1.111currently the routing is going to FG-FW01 with static ip route 0.0.0.0 0.0...

HeraldSison_0-1729088974829.png

is public to public NAT possible?

I have traffic flow like shown below -A Microsoft public IP > a public IP on our DMZ firewall on prem > NAT > an private IP on prem.Is it possible to configure FW to forward traffic as shown below?A Microsoft public IP > a public IP on our DMZ firewa...

tachyon05 by Level 1
  • 145 Views
  • 6 replies
  • 2 Helpful votes

VRF and redistribute connected command.

Hi guys,I currently have a router that doing EIGRP, below is its EIGRP:router eigrp Prod!address-family ipv4 unicast autonomous-system 150! topology base   redistribute connected    redistribute static exit-af-topology  network 10.10.10.0exit-address...

Resolved! Cannot launch sandbox

When attempting to launch a sandbox, I receive the following error message:"could not complete your request because of an internal error"This occurred when trying to launch Cisco Catalyst Center and ACI 6.0 sandboxes, and I have not tried other labs ...

AAAAMan by Level 1
  • 57 Views
  • 3 replies
  • 0 Helpful votes

StackWise and StackWise Virtual Difference

Hello, I’m new to Cisco and currently studying StackWise and StackWise Virtual. Both technologies seem to reach the same goal for high availability and provide single management interface. I wonder why both exist, especially StackWise is supported in...

Cisco ISE patch 7 cavelets

Hi Team, We planned to proceed with cisco ise v3.2 patch 7 is there any issue in this patch 7 after installation and service are working as expected and what about RSA PSS Enable bug? Is there any reported cavelets for this patch.Please help me with ...

GeoLocation IP Package Download In 7.4.2 FMC

We recently upgraded our FMC to version 7.4.2 and then 7.4.2.1, and I noticed in the release notes that they have added an IP Package Download option under the GeoLocation Updates tab in Content Updates.  In the release notes for 7.4.2, they mention ...

jmeetze by Level 1
  • 130 Views
  • 1 replies
  • 0 Helpful votes