Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1999469members
1359896discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

StackWise and StackWise Virtual Difference

Hello, I’m new to Cisco and currently studying StackWise and StackWise Virtual. Both technologies seem to reach the same goal for high availability and provide single management interface. I wonder why both exist, especially StackWise is supported in...

Resolved! ISE Profiler Update messages email address

We're running ISE 2.7 patch 6 - Does anyone know if we have the ability to set the sending email address that the Profiler feed's updates come from? Everywhere I've looked says these emails only come from the internal system address of ise@hostname F...

Failover VPN Tunnel will not come up

Hello together, I have configured a VPN Tunnel and the primary tunnel is working fine and is active. The Failover VPN Tunnel does not come up because it has the same address in the ACLs applied. When I try sh crypto session remote 2.2.2.2 (Backup tun...

Mocisco by • Level 1
  • 143 Views
  • 7 replies
  • 0 Helpful votes

Resolved! Finesse API for team config 12.6.2

Hello,I am facing an issue where I'm attempting to utilize the put request to update a team specific layout using python. Here is the python code (scrubbed for anything personal):import requestsfrom requests.auth import HTTPBasicAuthimport sslimport ...

ikev2 profile certificate map problem

I am trying to make two different ikev2 profiles for two different group of users. I am trying to distinguish between them based on the serial number of certificate. However any certificate that is issued by the CA always fall under the first profile...

HermanAkv by • Level 1
  • 562 Views
  • 20 replies
  • 0 Helpful votes

device profiling on WLC 9800 running IOS-XE

Hey everyone,Is there a way to update the OUI database in the WLC running IOS-XE.  I think there was a way with AirOS, but I don't see it in IOS-XEWhat I want to do us upload the updated OUI database from https://standards-oui.ieee.org/oui/oui.txt so...

Alex-Pr by • Level 1
  • 90 Views
  • 3 replies
  • 0 Helpful votes

Calling Name being stripped from SIP headers

Hello, I have a customer with CUCM 14SU1. They have recently purchased a VG410 which has 48 FXS ports which connect analog phones at one of their sites. The VG410 is not supported as an SCCP gateway until CUCM 14SU3 so I have set it up with dial peer...

Resolved! Split Traffic between 2 Firewall from my Core Switch C3850

The goal i want to achieve here based on from the diagram below:i want user1 - 192.168.20.x to pass FG-FW01 192.168.1.1i want user 2 -192.168.50.x to pass FG-FW02 192.168.1.111currently the routing is going to FG-FW01 with static ip route 0.0.0.0 0.0...

HeraldSison_0-1729088974829.png

is public to public NAT possible?

I have traffic flow like shown below -A Microsoft public IP > a public IP on our DMZ firewall on prem > NAT > an private IP on prem.Is it possible to configure FW to forward traffic as shown below?A Microsoft public IP > a public IP on our DMZ firewa...

tachyon05 by • Level 1
  • 156 Views
  • 6 replies
  • 2 Helpful votes

VRF and redistribute connected command.

Hi guys,I currently have a router that doing EIGRP, below is its EIGRP:router eigrp Prod!address-family ipv4 unicast autonomous-system 150! topology base   redistribute connected    redistribute static exit-af-topology  network 10.10.10.0exit-address...

Resolved! Cannot launch sandbox

When attempting to launch a sandbox, I receive the following error message:"could not complete your request because of an internal error"This occurred when trying to launch Cisco Catalyst Center and ACI 6.0 sandboxes, and I have not tried other labs ...

AAAAMan by • Level 1
  • 77 Views
  • 3 replies
  • 0 Helpful votes
Load more