PLB is covered in the configuration guide for VXLAN on Nexus 9Ks. But the explanations are a little thin.It might be a really good solution for my customer and save them investing in F5s or Netscalers.Does DCNM support PLB though I cant see it in the...
Forum Posts
HiI need to setup a new DC with Nexus 9000s with DCNM and VXLAN EVPN.The switches will be new and straight out of the box. Is there a pre reqs document anywhere on what needs configuring on the switches prior to discovering them with DCNM and using t...
Resolved! vPC for OTV Internal interface in 7700
Hi allWe have two sites (EAST and WEST) which will be connected with a pair of 7700s at each site through two inter-site 10G connections. We will create 3 VDCs in each 7700, one called Admin, one called Head, which will have the 10G inter-site circui...
HiWe are building a VXLAN fabric using Nexus 9Ks and DCNM 11.1.The release notes say that you can have the Border Gateway on the spines but this isn't one of the examples in the documentation so I am a little confused at what it will actually look li...
When using the fast reload option on nexus 3000/3100 series does the switch come back with the current running config before the fast reload? I would assume as a standard image update, reload would come up with current running config. I am just not s...
Resolved! OTV with FabricPath implementation.
Hi, We have two DC running individually on fabricpath. Now as per new requirement we want to run VMotion between cross DC's and span same L2 network on both DC's using OTV to create new OTV VDC in nexus 7K's "On a Stick" mode which does not required ...
Hi, I have dual N9K VPC pair of switches at 2 locations.I am using VPC's, but for the inter-site connectivity, I intend to create 2 port-channels of x4 10Ge between switch 1 and switch 2 at the different sites. site A ...
Hi Master, We have a couple new deployment nexus 93180YC with NX-OS 7.0.3.I7.6.We have configuring the vpc domain, and vlan database. Its like and must be same with peer switch, but i have still facing Please check "show vpc consistency-parameters vp...
HelloCan you tell me what these sentences mean? "Provides single-touch site configuration""Preserves existing Layer 3 failure boundaries""Provides automated multihoming" These are discussed in the following linkhttps://www.cisco.com/c/en/us/solutions...
Hi, Does anyone know if a 100G port on the N9K-C9336-FX2 can break out into 2x50G QSFP28 ports? I've looked at BRKARC-3222, as it suggests the ports are "100G/50G/40G/10G with breakout capability", but I cannot find a specific mention in Release No...
Hello. I have a cisco N10 6100 (layer 3) switch and nexsus 2000 router.I want connect them with each other , but if I'm not mistaken nexsus 2000 worked only with nexsus 5000.How con i connect nexsus with cisco, if possible.
I have some 9336's running version 9.2 with the proper EPLD installed. I'm being told due to some odd behavior that I should downgrade to the suggested NX-OS line of 7.x. My question is, should I also downgrade the EPLD from 9.x to 7.x before the ...
N7k device , F3 card. I have 3 ports in port-channel. The moment i remove any physical ports from port-channel , using No channel-group cli , qos policy applied on port-channel not working. Could anyone help me with the expected behavior. What i fo...
With our current deployment we are pair of nexus 7000 running multiple vdc. Nexus 9000 running ACI mode is there support for running isolated environment similar to the vdc?
We have Nexus C93180YC-FX as leaf switches in ACI mode. When I see the interface status, it is seen that some port speeds are seen as inherit and some are seen as 10g after putting 10Gbase-SR in all.These ports are at default status and are not confi...
