Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Does this need to be done with ESXi 5.0 and CUCM 8.6.2? I don't see any 5.x versions in the wiki page:http://docwiki.cisco.com/wiki/Disable_LRO
Hello,We've got CUCM 8.6.2 and have a SIP trunk from our provider going through a CUBE. Today everything is working well. Because of a few ordering/design issues, we're getting ready to port one of our remote site's numbers to our SIP Trunk and the...
I'm trying to find out what the difference is between a CTI route Point and a CTI route Port is. If anyone can shed some light on this I would appreciate it. ThanksJason
Hi,I am not dedicated voice guy but got task to remove server from Disaster Recovery System Scheduler because it keeps sending alert email as below:Backup process failed. Investigate sftp server settings. Reason : DRF was unable to backup component P...
Cisco IOS Software, C3900 Software (C3900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)I want to change a CAS e&m-wink-start to a PRI on controller T1 0/1/0 using mgcp below. I am posting the new configuration below the current e&m-wink-...
Hi All,I have a problem with my Call Manager trunking to Avaya. Calling to PSTN is routed to trunking Avaya with Pattern 0.!the problem was if i dialed pattern to some our provider like 0878XXXXXXXX , the call was unsuccesfull. but for number of othe...
In CUCM 9.1, I noticed that there is no dial tone on FXS port on VG224 when prefix DN is configured in CUCM.If we remove the prefix DN, then we can make calls. This seems to be new because this is working in CUCM 6.1 and 7.1.Any parameter to change o...
Hello,we want to deploy Cisco UC for install TelePresence system in future. At first, we are going buy some licenses - about 30 CUWL seats, so Business Edition 6000 is good choice. But, we already have Cisco UCS 5108 blade server with VMware vShpere ...
Hi,I´m having problems with a 3925 router since doesn´t recognize the voice-port command. The current IOS is (C3900-UNIVERSALK9-M), Version 15.1(4)M4I haven´t installed the PVDM3-32 card yet, my doubt is if once I installe this card the voice-port co...
My scenario is the following:Region A Sites (east coast offices) ---------------------------------> CUCM --> Centralized CUBE B --> SIP Provier verizon Region A SBCCisco offices (direct registration to CUCM, no SRST)PBX Sites (MGCP integration with C...
I have a PRI on the router that is configured and it is up. I setup everything in CUCM like a few other sites we have. Hooked up a phone and they are able to make outbound calls. I can also reach that phone via extension.But when I try to call the...
Hello everybody!i have got a Cisco Unified CM version 8 and i want to use enduser informations (for example Firstname and Lastname) as alertingname (call signaling).Is it possible and how it works?Thank you!
Recently I've had a string of WAN 'blips' that caused the phones to fall back to the gateway. Most of them re-register back to CallManager after the outage is fixed, but it seems as though a few get stuck on the gateway...i've watched the timer coun...
Hi AllI have a CallManager I'm suppling remote support for at present and we are having certan calls fail with a code "Progress Ind i = 0x8582 - Destination address is non-ISDN"Calls are routed from CUCM to Cisco VG then connected via E1 to a privete...
Hi,Can any one help me how to change the system message in CUCM 7.1(2) " Your Current Options" to another text.Thanks...
