Hi people, Usually when i did configure a cisco phone i tape the info on the call manager (maccaddres, extension number, extension name, etc.) and when i put the phone on lan he went to looking for the call manager, the call manager sent to the phone...
Forum Posts
We have 100+ 7925G wireless phones that we configured the EPNM on the primary line for each phone. Where the Phone DN used to be displayed in the upper right corner of the phone screen is now the EPNM. Is there a way to change it back Wireless Phon...
We started having issues with a number. The number is 4500 (omitting the full 10 digits). 4500 rings in on CenturyLink SIP Trunk. This has been working for years. No recent changes.4500 is a CTI Route Point for a UCCX trigger. We started getting comp...
Hello, We have been having some issues with voice recording, only one side of the conversation is being recorded, Cisco side. Examples of two different calls: Cisco phone (local Cluster CUCM 11.5) to an external number (PSTN) over a Voice Gateway on...
I'm unpicking some of the dustier corners of our CUCM setup and hit something I can't work out. We've got some MGCP Euro ISDN-30 trunks. With Euro ISDN, the leading zero of the presentation number is not sent by the network. Yet when the presentation...
I have an 8851 configured in SIP mode with Asterisk, tftp server has a directory Desktops/800x480x24 with List.xml, and the image + thumbnail inside. Image is 800x480x24 as a bmpthumbnail is 139x109x24 as bmp thumbnail renders on the wallpaper select...
Resolved! Destination pattern ?
Hello, quick question . what is the difference b/w these two destination-patterns? I have a dial peer configured and I was told to change it from #1 to #2 destination-pattern ^310928230[4-5].destination-pattern ^31028230..Thanks!
Hi, We have deployed CUCM 12.5 for a large enterprise, now they would like to share the same infrastructure for one of their sister organizations. The parent organization has the complete admin control for the collaboration infrastructure; however th...
Resolved! CUBE memory requirements
If an old CUBE data sheet says what is shown in the attached image, does this mean the 2911 will support 200 SIP trunk sessions with the DRAM specified? Not that 512MB is the minimum DRAM, and 200 is the max SIP trunk sessions possible with whatever ...
Greetings All,We're looking for a relay that will pull in using the ring signal from an "FXS" port on a Cisco router.Router: ISR4331 (with "FXS nim" card).Buzzer or horn: 120Vac.Port has been configured (FXS) to ring but I'm not able to measure ring ...
I have ATA 187's and 190's, some with most recent firmware some with older firmware that were working fine on older switches. Hardware upgrade to CAT9k running 16.9.4. After the upgrade random ATAs will not pull an IP address unless I strip the co...
Resolved! Compatibilty
Hello, I'd like to know if the following phones are compatible with the Plantronics CS540 headsetCisco IP Phone 6851 Cisco IP Phone 7841 Cisco IP Phone 8841Thank you!
Hello everyone, As we know "Route next hop by calling party" feature in Translation pattern is wildly used to block/allow calls based on calling number. There are tons of doc in web on how to implement the same. I am trying to use this feature to imp...
Hi Community,im facing an issue on the CUCM cluster 12.5.1.11900-146 everytime when I reset a phone(doesnt matter if its 794x or 7841 or 8851) the MD5 and SHA1 checksum value of ITLFile will change and sometimes I get a known issue:Verification of th...
Dear I have CCM 7.1.5 and i am tring to upgrade 7921G device pack but it is giving me " no valid upgrade options were found " and i am using FreeSFTP do you what is the problem that i faced and how to solve it ???? Note : please see the attached file...
