hi,on documents it is said that we could not install LMS4.1 10K on a VM ware ,does it mean it even I install windows server on a ESX 4.0 I could not install LMS on that windows ?and please tell me where I can get the prices !!thank you
Is there any help for the table fields in Alert and activities ??for example in the commponent table there is IF-192.168.100.1/92 [Tu1011213001] [MPLS-**] I dont understand what IF means and what is the number 92 after the IP ??Thank you
I'm trying to populate the graphics authentication (portlet). The UT is collecting and CM data too.In Work Centers > Identity > Dashboard i selected the devices, but the graphic still empty:I tried to run a report: Work Centers > Identity > Reports (...
I need to implement a "Spanning Tree Status" view on my NMS and I would like to use SNMP. I'm running Rapid Per-VLAN Spanning Tree Protocol on 3560-E (WS-C3560E-24TD) with IOS 12.2(55)SE.Using the ciscoStpExtensionsMIB MIB (CISCO-STP-EXTENSIONS-MIB) ...
Hello,not sure if the ME3800X is currently supported for netflow? It takes the commands ok but we cannot get export:lonppe01#show ip flow interfaceGigabitEthernet0/3 ip route-cache flow ip flow ingress ip flow egresslonppe01#show ip flow exFlow e...
We use Cisco Prime LAN Management Solution Version 4.1 to maintain and monitor our 1000 Switches. In addition to this, we use Kiwi-Syslog. Now I have a problem I can not find out. 2 of the switch (WS-C3750G-48PS-S) reports that the CW has tried to lo...
hi;when I try to open the topology services I recieve the error Cannot connect to the ANIserver .... even when I am on the server itself .I've found out it is due to my DNS problem, here is the scenario;I installed the LMS on the server just before ...
HiWhat i want is to have LAN and WAN connections using one Cisco SF302. I'd like to have 3 ports or more for WAN and rest of the ports for LAN. At the moment there is WAN and LAN configured to DRG700. Question:How do i configure Cisco SF302 to have a...
Hi folks, Let's take the output below as an example:Router#show logging
<-- output ommited -->
Jan 10 23:10:54.723: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
Jan 10 23:10:55.723: %LINEPROTO-5-UPDOWN: Line protocol on Interface...
Hello everybody!I have simple but annoying problem - i'm trying to implement archive command but my devices don't do any automatic configuration backup. When i hit "archive config" or "write mem" it backups configuration perfectly, but after that no...
Hi, I want to upgrade a Cisco Works LMS from version 3.2 to 4.1. Actually there is a 1500 device license in place. For the upgrade I need only 300 devices. Can I purchase the LMS41-300-UP-K9 to upgrade from CWLMS-3.2-1.5K-K9. What is neccesary (perha...
Our client have integrated Clarity NMS to Ciscoworks LMS 3.2.1. So far they are receiving raw alarms/snmp traps but it lacks information/inventory of the originating device. Kindly see sample raw alarms below:2420: 2011-11-25 12:10:46 Received trap =...
All,I need help creating the ODBC Data Source on windows for connection to the IPM database. I have successfully connected to the cmf and rmeng datasources. However, the dbViews_401.pdf does not provide the TCP connection parameters for the IPM/IPS...
Dear friends,Please, I need your help to know if there are any needed licenses to upgrade my CW-LMS-3.0 to CW-LMS-3.2 ? do I need to purchase any licenses ? or just downloading upgrade package from cisco.com will be enough ?
