Hi Experts,I am not sure if this is the correct community to ask this question.But, if anyone could recommend if, for preparation for 200-301 certificate, I would need to get the CCNA 200-301 Official Cert Guide, Volume 1 or CCNA 200-301 Official Cer...
Forum Posts
Hello everybody, when I type "show lldp neighbors" on my 2960, I have an output like this: POLI-61A-192.168.100Gi1/0/25 120 B Gi1/0/25The first column represent the remote device ID, but it is cut to the first 20 chars only...
I have successfully imported my building and floor plans into Prime 3.7.I have the AP's populated in the Access Point Radios Unified AP Radio section.At one point I was able to add the AP's to the floor plan maps.I then logged out and back in and the...
Can we do CCIE Routing exam without any prior Certification ?
On page 721, the Solicited-Note Multicast address is defined as FF02:0000:0000:0000:0000:0001:FF__:____, with the last six digits being the "Last 6 Hex Digits of Unicast Address". So why does Fig. 31-4 show PC2 with IPv6 Address of 2001:DB8:1111:1::...
I'm trying to manage my switch but Network Assistant 5.0 and 6.0 tell me that is unsopported.If I check the datasheet of the switch seems to be supported as the F.A.Q. that I attach below. Q. How do you manage the Cisco Catalyst 3650?A. The Ci...
Hello all. My config on IOS Catalyst 2960s is this:username bckup privilege 3 secret ... <omit> privilege exec level 3 copy running-config tftp privilege exec level 3 copy running-config privilege exec level 3 copy privilege exec level 3 show runni...
everything on the right of the College router is my inside network, i can ping outside (my classroom computer) College router is connected to the classroom router together with all the host PC, i put this command inside college to enable ping between...
Resolved! Nexus OSPF RIB logging
Hi all Is it possible to syslog the output of 'show ip ospf event-history rib'?switch# sh ip ospf event-history rib OSPF RIB events for Process "ospf-1" 2020 Jun 11 09:22:15.033976 ospf 1 [9643]: : Done sending routes to URIB 2020 Jun 11 09:22:15.03...
Resolved! Certifications
I am changing careers, going into IT more specific networking. I have no experience and thought it might be best to become A+ certified and get a job as I study for the CCENT exam. Has anyone taken the A+ certification exam, what study tool did you u...
We are installing a Metro line. The ISP gave us a /30 address for the WAN side and /29 on the LAN side. We are supposed to use the LAN side for our 6 public addresses. I don’t know how to setup a WAN and a LAN side and connect (route/NAT) them. I...
Resolved! sg300 port problems
I have a very standard setup. SG300 52 poe, vlan1 and vlan3. Polycom phones on Vlan3. 4 or 5 ports on the switch aren't working as expected. I plug the Polycom phone to the bad switch port and it powers but then displays Dhcp failed. Every other port...
Hi I working on at large European enterprise company with multiple devices, primary switch´s 29xx, 3650, 3750, 3850, 4500, 93/9500. I’m tasked with finding a nice an easy way, of making sure we have up to date and stable software running on all devic...
Hi Experts, does anyone know a OID to fetch the configured duplex value of different interfaces of a 2960S/X?I tried OID 1.3.6.1.4.1.9.5.1.4.1.1.10 but I only get the negotiated duplex value, not the configured. For example:Interface Gi1/0/1 is confi...
