Hello,I was wondering, how to create, save, and run a TCL script on Cisco c4500 [Cisco IOS XE] performing a traceroute and saving the output to txt file. Thanks,
Forum Posts
Our Devices including acc, dist and core has almost all snmp traps enabled. My concern is if enabling all traps will have affect on network performance. Shall I only enable the traps that we need or shall I keep all traps enabled. What is the best pr...
%ASA-4-733100: [ x.x.x.x] drop rate-1 exceeded. Current burst rate is 9 per second, max configured rate is 10; Current average rate is 17 per second, max configured rate is 5; Cumulative total count is 20831 Can someone explain me what is the meaning...
Hello! I want to create a policy for search unwanted, undesirable commands. Example, I have an ACL: ip access-list standard ACL_TEST 10 deny any If anyone adds here a some command, example, like this ip access-list standard ACL_TEST 5 p...
Hi everyone, Can anyone explain me complete step by step procedure to upgrade Cisco-4500-VSS ios with precautions and things to do during and after upgrade process. Any help will be appreciated. Thanks,
Hello, I am fairly new to the networking field, and I am trying to design a network setup using a Cisco 1921 router and a Cisco Catalyst 3550 switch. After doing lots of research and running into multiple road blocks, I had some questions for the Cis...
Resolved! need to remove TRACKING-5-STATE messages
Hi.I'm using this config to see what's happened with a link:=============================track 1 ip sla 1 reachabilitydelay down 30!track 2 ip sla 2 reachabilitydelay down 30!track 3 ip sla 3 reachabilitydelay down 30!track 4 ip sla 4 reachabilitydel...
Hi AllI have a Cisco Switch model c2960-24TT-L with iOS "c2960-lanbase-mz.122-35.SE5.bin" which upgraded to version " c2960-lanbasek9-mz.122-55.SE12.bin" recently. After Upgrading, the Switch Boot Up normally( All POST Passed), but the SYST Led get A...
Resolved! Router id and bgp configuration
Hello, i have a problem while doing basic configuration. I can't set router id of any router to any price. I've tried using and loopack and it still doesn't change. It stayes at "remote router id 0.0.0.0. and it gives me a message to do it manually, ...
Hello, this switch was pre-configured by our vendor and I know very little about cli's. LAN1 and LAN2 has two different ISP address(for redundancy) pointing to our remote server. How can I test/ping/trace the connection of each ISP going to our remot...
Hello, I'm trying to allow cacti to only graph a single port on our Cisco 6500 Sup 720 Router.Specifically port te4/1 which has index of 202.TenGigabitEthernet4/1: Ifindex = 202 I know command to allow it would be:snmp-server view test ifEntry.*.202...
Dear Experts, I've a question regarding setting up the threshold value for an access switch and also dist switch interfaces. We have Prime and another NMS where in we have to set up threshold value for error and discard alarms. As of now, by defaul...
I have an architecture like below: Site net --- local router --- border router <===VPN===> HO router --- Netflow collector I´m trying to send Netflow traffic from local router to the Netflow collector back in the Head Office server. Traffic is no...
Hello community, We are having the next problem: We are trying to add a new SPA (SPA-5X1GE-V2) by OIR, but the ASR doesn't detect the new card, it doesn't go up. RTTMCPDCOR01#sh hw-module all fpd ==== ====================== ====== ===============...
Dear Expert, We have Prime and we are monitoring wireless. We are receiving a huge number of alarms from WLC regarding the interference and Noise threshold alarms. I have searched about setting up threshold and could only find an article which says...
