Does the 7905 support srst ?I have a 1760v running on 12.3(7)T and srst doesn't work for the 7905 and works fine for the 7920
Does the 7905 support srst ?I have a 1760v running on 12.3(7)T and srst doesn't work for the 7905 and works fine for the 7920
Anyone familiar with locating PRI errors on a Catalyst 6000? The only command I can find is show port voice fdl which seems to give some error information. I'd like to be able to monitor any circuit disconnects. I've set up syslog as well, though ...
Hi,I have a 2600 router with two VIC 2Fxs cards on it. I have created 4 pots peer for the same. The problem is when I make a call from one Fxs card to another there is a lot of echo being generated. If I call another extension within the same card th...
I have a customer who is having trouble with 7910 not registering.They have two sites Callmanager 3.2 and 3.3.At both sites the occasional phone will become unregistered.To fix this they have to go into the switch port config and shut the interface t...
Has anyone done an integration between a Lucent PABX Definity G3r V11 with an MGCP gateway running QSIG? A sample config would be nice.
User/network hold audio source for the MOH can be defined on lines, device and device pool. Which one will take precedence over?
Oh, If this were only a joke...Here's what I have:CCM 3.3.3r36509 running CatOS with 6608(Using 2PRIs 1 T1) , 10/100 (PWR), WS-X6182, SUPs and MSFCRAS with own PRI used for dial out support only.Here's what I am tring to do:The PRI for the RAS is goi...
Which CatOS is the most stable version to run IEEE inline power? Thanks.
We've just upgraded to 3.3.2 SPC and are using a Cat 6000 (6608 E1) for PSTN access. When an external caller hangs up, the line is not disconnecting, instead we get the Telco disconnect message (e.g: the other person has cleared).This is causing big ...
I want to use softphone from SOHO via dial-up, but when I did a test with a call, the voice is hard to understand, the voice breaks up.How can I use the Softphone from SOHO?Are there a solution tu use it ? Thanks for your help.
I had noticed MOH being flooded from a port on a 3550 switch. I can toggle the "voice vlan x" command on and off and when off the multicast is no longer flooded to that port. Is this normal behavior? If so why is it necessary? Does the phone not act ...
CCM 3.3. Can we create a department bill report base on the department created under the global directory? Currently the department bill report shows the user id. Thanks
Hi,I know that under the multiple H.323 Gatekeepers environment, we need to fill in all information on all zones and their prefixes on every gatekeeper. At the same time, we can assign the "bandwidth" command on the communication with any particular ...
When i do a search in ccmadmin for a specific user I get this message after a few minutes."getUserInfoBySimpleFilterLooking" When I do a blank search all the users come back but I get this message when I try to view the properties of a single user. I...
i try to permit with NetMeeting to call on phone IP register on a callmanager.My callmanager register it on the gatekeeper like "VOIP-GW" but after a little time it has been disconnect from it, and during the time it is registered the calls aren't ac...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-02-2025 09:00 AM | ||
03-30-2025 11:51 PM | ||
03-22-2025 10:34 AM | ||
03-17-2025 03:19 AM | ||
03-15-2025 12:31 PM |