Hiwe are using cisco 7902 series ip phone.i want to activate speed dial facility and abbreviate dialing in it,but how to do that.(Cisco Call Manager 4.1) Thanks
Hiwe are using cisco 7902 series ip phone.i want to activate speed dial facility and abbreviate dialing in it,but how to do that.(Cisco Call Manager 4.1) Thanks
Howdy,trying to get background images onto a home system with CME 3.2 and a 7970G.first off is this possible?second... if so what would the syntax for accessing the list.xml on the flashbe ??
Hi, I would like to know if it's possible to add and configure IPMA Users (Managers and Assistants) by using AXL ?Thanks a lot,Bruno.
Hi guys,Has anyone been able to get the 7914 Expansion Modules to work on a version 3.3 CCME?I have it already working with the 7960 but can't seem to get it on the 7970Do you know if there is a specific firmware or CCME version that enables this?
Hi there,I am having an issue with low volume of voice going out, incoming is fine.I have a 2801 with PRI and a couple of 7911 phones.I have tried the "output attenuation" command under the voice port, but it did not make any diference, even between ...
I have an ATA 186. Both ports are registered with CM no problem. CSS and PT are all fine. When I put an analog phone on port one everything is fine. When I put it in to port two, the analog could ring IP phone but get busy tone when user pick up ...
Hi The following link is not active. Does anybody have a valid link?http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/ccmcomp.htmThanksAti
Is the model number ws-c2960g-24tc-l an IPV6 capable switch?
Hello everybody, I would change ths logo on a 7911 too, but it's not working with a Call Manager version 5.1(3) I've doing all the stuff described on the document http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7906g_7911g/5_1/sip/english/admini...
Hello,We're using Cisco IP Phones 7971G-GE connected to a Cisco switch 3560G PoE-24 on a Cat6 network. The version of the Call Manager is 5.1.1. The switch, phones, servers and clients are setup to use a port configuration of 1000Full (we tried in au...
Hi!I am observing a strange problem, which appears to be never solved by anyone (I did some internet research with no luck).What I have is AS5350XM with roughly the following configuration (I'll post the relevant "sh run" snippet below, now it's just...
am I the only one with this many problems with this release, database corruption, not replicating correctly, voice mail issues with jtapi to unity express, directory numbers not found, moh on hold intermittant
Hi all,I have a CE500 Switch(WS-CE500-24PC), as I forgotten the password of the switch I need it to be reset to the factory default. As it doesnt have any console port, I was following the link below to reset the password. http://www.cisco.com/en/US/...
Call flow:1. Call comes in and gets sent straight to Unity.2. If the caller presses "0" or times out, the call is directed to the receptionist.3. If the receptionist does not answer, the call is transferred to another extension which appears on about...
We are running AutoQoS but have recently migrated our WAN service that puts our IP connectivity to a sub-interface (interface serial0/1:0.500 point-to-point and a frame-relay interface-DLCI). In our prior WAN configuration we bound the IP address dir...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-17-2024 05:55 AM | ||
07-15-2024 12:39 PM | ||
07-09-2024 04:24 AM | ||
06-20-2024 05:44 PM |