I have a problem in the atm interface,loss conectivity intermittent.I throw it thecommand:show dsl interface atmWIC Config Reg2 0x03 Gen bus error on bad ADSL accessInt 0 Enable Reg 0x03 ADSL normal interrupt enabled ADSL e...
I have a problem in the atm interface,loss conectivity intermittent.I throw it thecommand:show dsl interface atmWIC Config Reg2 0x03 Gen bus error on bad ADSL accessInt 0 Enable Reg 0x03 ADSL normal interrupt enabled ADSL e...
Dear all,I write you because when I reload my router 826 (After that I did a write mem)I lost the date and time settings,that I previous set with the command clock set.The config register is 0x2101.Thanks & regards,Igor Fabrizio
Hi, I have one inside interfaece and one outside interface. When I enabled nat in the outside interface as "Ip nat outside" and gave the global command as "ip nat inside source list natlist interface Loopback0 overload" .But I didn't mention in t...
whythis error is coming in the router. What is the solution for this .The error is "Jan 18 06:57:52 GMT: %STANDBY-3-DUPADDR: Duplicate address 10.155.101.3 on Ethernet0/0, sourced by 0040.eff2.75f2"
Recently we were discussing the pending replacement of a few VINA routers which currently terminate our T1's with ciscos. We also have cisco 1721's right now on the inside of the VINA's connected into switches with our other firewalls and such. The...
Hi!does anbody knows how to limit the bandwith that goes in and out of a Fasthernet port in a 3550 switch.In that port we have a Server that shouldn't transmitIP packets (or Eth packets) over 200Kbs
When creating a new VLAN interface on a RSM, will the interface be down/down until a machine is connected to the 5500 and configured for that VLAN?Many thanks,Daniel
Does Eigrp send routing updates of secondary addresses once the adjacency is formed on the primary interface?
It's known that EIGRP doesn't form adjacency on secondary addresses but are the secondary routing updates sent to the neighbor once EIGRP forms adjacency over primary addresses?
Hi,Pls find below,some lines from OSPF design guide "A router that has interfaces in multiple areas is called an area border router (ABR). Routers that act as gateways (redistribution)between OSPF and other routing protocols (IGRP, EIGRP, IS-IS, R...
Hi all,i cannot find the true performance of the above switch , and the previous 2950 3550 family.I need the following true parameter for :switching fabricforwarding bandwidthforwarding rate Also what are the maximum reccomended svi's on3550 3560 and...
1.We are on line share trader we are using lease line connectivity as a transparent bridging with BSE&NSE server as well as inter office connectivity also can you please suggest now we do not want to use bridging configuration we want to use routing ...
I installed a NM-1T3/E3 module in one cisco 2621xm and the "sh ver" command seems to show that the router is recognizing it:**************************************************ROM: System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1) R...
Can someone point me to a basic config to allow me to get layer 3 traffic between a 3550-EMI with hosts using 10.29.252.0/24, and a 3550-EMI with hosts using 10.29.253.33/27?The 3550s are connected using Fa0/24, and need to use EIGRP.Thanks,Brian
I have configured a layer2 port-channel between a 2950 and a 6509 as below however the channel never came up.Config used EDGE 2950 CONFIG2950#conf t2950(config)#interface Port-channel32950(config-if)#switchport mode trunk2950(config-if)#switchport tr...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |