pls, I have a 3600 + 1 fastethernet card, the router will reset when the router connected a 2950 or I config the fastethernet's subinterface .pls help me! and thank you !
pls, I have a 3600 + 1 fastethernet card, the router will reset when the router connected a 2950 or I config the fastethernet's subinterface .pls help me! and thank you !
I'm a installing one NCM for a client Demo.From this link I found that I need to contact TAC to get a license:http://www.cisco.com/univercd/cc/td/doc/product/rtrmgmt/cw2000/ncm/ncm1_0/ncm_lisc/ncm_lic.htmSince I've open a TAC case but still have no C...
hi,we have a 3640 router with 4 slots free. i have an NM 1E2W module inserted in one of the slots and in that NM 1E 2W i have inserted a WIC2T wan card. problem is that it is recoginising the NM Module while boot up but not the wic2t. i am not able t...
Hi!Is it possible to be configured 10Mbps ethernet(AMD Presidio2,2611 IOS12.0(7)T) in full-duplex mode? Regards
Hello everybody,After updateing IOSfrom: c1700-k9o3sv8y7-mz.123-2.XE.binto: c1700-k9o3sv8y7-mz.123-8T.binon a Cisco1760-V3PN/K9i can not save the running config. By console, by telnet ssh, by SDM 1.2IOS Message:myxx# copy runn startDestination filena...
For some reason the file "strtserv.bat" was not copied during the nGenius 1.4 install, therefore I'm unable to start the server up. Could someone please post/email a copy of, or the contents of their "strtserv.bat" file. The file belongs in the <nets...
We are planning to set up an ethernet network for our office. The primary network traffic consists of connections to the SAP server, Lotus Notes server and a few Intranet servers located centrally in the "IT Building". In the 4 LAN segments that we h...
Hi,I have 2x 2950 switch... Possible to do the following?Switch 1 - Port 24 destination port and cross cable to Switch 2 - Port 1 Switch 2 - Port 1 as a source port, and i will have a IDS Sensor at Switch 2 - Port 24 destination portWill the traffic ...
Say I have 3 switches all connected with redundant links. The switches converge for 30-50 seconds. During this time, will the devices on each switch still talk to the devices on the same switch, or, does EVERY port on the switch go into blocking? ...
Hi All,The scenario is like this :I have created 2 Vlans with 2 IP addresses (Vlan2 and 3). I have a third segment that is found behind a device (this device is on Vlan 3). Therefore, I did a static network route for the third segement pointing to th...
I have configured NTP (Network time protocol) on one of our windows 2000 server and we have tested NTP server by configuring the clients machines andclients machine are able to synch the time from this server but we are not be able to configure the r...
Hi all,like to know how to monitor a vty exec session. I want to see which commands are typed. Is there a way to achieve this? Thanks, Nils
HiNot sure if this is the right forum, but here goes :-)I have tried to upgrade the firmware of a Cisco 677 using tftp and management cable, but after several failed tries I cannot even get into rommon mode using the management cable and hypertermina...
Greetings. Is there a way using the access-list to allow one NAT workstation access to only one web site while allowing all other workstations on the lan (also NAT) access to any address on the website?Thanks,Jeffrey
Can MSFC be removed from WS-X6K-SUP1A-2GE safely ?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |