has anyone tried to use the threshold manager (cww6.1) with cisco catalyst 3750 ?I get the message that the device is unsupported. But in the CWW6.1 supported device table i can see that this device should be supported.
has anyone tried to use the threshold manager (cww6.1) with cisco catalyst 3750 ?I get the message that the device is unsupported. But in the CWW6.1 supported device table i can see that this device should be supported.
I´ve issued the "ntp server X.X.X.X" command on some switches and I observed that the "ntp clock-period" parameter has not been installed automatically on some of them and the ntp status shows "Clock is unsynchronized". All the switches has the same ...
Hi,Does anyone know how to create reports from a Network Analysis Module in a cisco 6513 switch? I don't have a "reporting" tab like I read in an article. Maybe I need an update to the module firmware?thanks for any help.ted
I would like to connect a 3550 switch to a 3745 router utilizing an FastEther channel. I located documentation on how to connect a 7500 router to an Catalyst 6500 but is doesn't work with the 3550 and 3745. I can get everything configured but can n...
Is there a standard value for the ATM VC values on ADSL circuits installed in the UK? I've been asked to configure a router for connection to an existing circuit. No one I talk to can tell me this information.
Hello,I recently installed a 16AM on a 2610 router.I configured the async 33 interface to accept incoming call everything is ok but after connected (using my laptop modem) I can't ping outside the Ethernet inteface.I enabled routing and directed-broa...
A router (R-1601) receives a default route via RIP from a L3 switch (C-6500).R-1601 is also configured to generate a default route (default-information originate). When everything is working fine (normal operation), the following can be seen from R-1...
Hey.. sorry for the probably ridiculous newbie question... but I just went through initial config on a 2950 and chose fa0/1 instead of VLAN1 for the Management LAN. How can I change it back to VLAN1 without having to reload? Anyone know the comma...
Does anyone know what is the command to send a dummy snmp trap from a cisco 3600 router to a NMS.I know Cat 6500 can do it, so I guess there is a way to do it on the Cisco router.
I am confused about VTP, and I'm sure someone here can clear up my confusion.Currently, most of our closet switches are set as VTP clients getting VLAN updates from our core switches (6500's). When I do a "show vlan" on the closet switch it will sho...
Hi,I'm trying to set up an 802.1q trunk between the buit-in 10meg ehternet port on a 2611 router and a cat 3524 switch. I am running release 12.2(11)T10 on the router. The subinterfaces will come up but I can not ping any devices on the vlans on the ...
Hi. I finally got bgp setup nicely on 3 routers on our network, but now I am noticing drops in traffic according to my snmp gauges and graphs.Here is a picture of one of the routers:http://poor.j3w.com/~tzulo/yipes-graph.jpgThe network topology is qu...
Hello, I have three vlans on a 3550-24-EMI switch. When I add the fourth vlan. It appears good. I do a show ip route and it displays only three routes.
Do they work the same?
Okay, so I need to be able to have a device plugged into my 4506 that will need to be referenced from two seperate IP addresses. I was led to believe that I could simply sub-interface this port and be done with it. However, the basic feature set does...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-07-2024 07:08 AM | ||
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |