Resolved! ccnp-recertification
hi,if i want to recertificate my ccnp status.is it enough to make the composite exame 642-891 ?
hi,if i want to recertificate my ccnp status.is it enough to make the composite exame 642-891 ?
HiI am looking into some remote site router upgrades and I cannot seem to find a way of determining whether the routers are 1603's or 1603R's. I have looked at a "sh ver" for the two different types of router and can't see any blatant differences. ...
I heard that when the primary line is restored, since the static route is still inside the routing table, BGP route won't move from BGP table to routing table thus ISDN won't disconnect.Any suggestions to resolve this problem?I need to know this urge...
Align-Err - frames that do not end with an even number of Octets and have a bad CRC) Can someone give me example?FCS -Err -The number of valid size frames with FCS error but no framing errors. What can cause these errors.Undersize - Can someone give ...
Operating 100Mbps Full on both ends. Restart of a controller using National DP83816 Ethernet Chip results in significant FCS and Alignment errors that continue until a change is made. Duplex reported OK at both ends. Pulling UTP cable for less than ...
Hi,I have a 3640 with locally configured usernames and passwords. I need to find a way to log when users connect and disconnect their dial-up sessions.I cannot move to a Radius/AAA solution and was wondering if anyone had found a way (or software ap...
My organisation is connected to the internet via a 64 k dataline. I use network address translation(NAT) and access list on my router to map internal ip addresses to the outside and give staff access to the internet. The problem is that internet traf...
Hi all,I have applied on an dialer interface both an output bridge list (with the command bridge-group output-address-list) and a dialer listMy question is: if a bridging traffic is filtered (denyed) by the bridge-list, is this traffic able to trigge...
What is the Maximum theoretical MTU siz for Fast Ethernet. Can it be as high as 4440 bytes?
If and how are this configurations used? Actual is the configuration at the NVM-ram running. Exist a description about the handling of this?Directory of webflash:/ 1 -rw- 705 ConfigExp.cfg 6 -rw- 252 IPCPSubnet.c...
Hi, after the flash initialization the switch sends a message:Exception (##)! Then it goes into a loop and never stops....Below is a sample of the situation. Any idea? Thanks.Initializing C3500XL flash...flashfs[1]: 2 files, 1 directoriesflashfs[1]: ...
One of our small sites is using a Cisco Catalyst 3500XL switch (24 Port) for office connectivity. In the past week intermitent network issues have come to light in this office including loss of network shares-printers-Internet.....Investigating furt...
Why do I get %error opening TFTP/255.255.255.255/network-configin my new router (Cisco 1721) , it is configure in a private network both serial and ethernet parameter but everytime I power down the router and power it up again this error messages ap...
Does anyone know if all Cisco 2950 24-Port Switches come with 2 uplink Gigabit Ports?I read the documentation of the switches, but it is not very clear. Seems like that only specific 2950 24-Port switch comes with the 2 uplink ports, not all of them...
I want to monitor a Portchannel (2 fastheth) in Trunk with a probe system.On 2950 the command in glob conf mode is "monitor session" etc.Unfortunately the system respond with a message like this: UNSUITABLE will not join any port-channeland the portc...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM | ||
11-08-2023 03:38 AM |