We are an isp and offering connection to 1 of our customers between israel and us.customer complain that when he do a file transfer from isreal to us he is gettting only 0% of port speed wich is 512k.whe he is testing from us to isreal he gets 100%.I...
I have a Cat 5513 with a RSM. The RSM has numerous Vlan's configured. I'll use Vlan 8 in my example.When I do a "Show Interface Vlan 8" on the RSM, I notice it says the bandwidth is 100mb. This is the same bandwidth listed for each Vlan in the RSM...
Does turning on RIPv2 authentication (MD5) increases the RIP packet size. If so by how much. What's the lowest Cisco IOS version that support RIP authentication.Thanks.sweeann
Mi pregunta es la siguienteTengo 24 hosts conectados a un hub..EL curriculum dice que el promdio de ancho de banda para cada host es:si el ancho de banda disponible es de 100Mbpssería:Promedio ancho de banda=100/24=4,167 Mbps por host.Esto que me ind...
Hi All, I'm new to BGP and I have a question regarding a config. in my internet router. we're running BGP via 2 ISPs but our hardware is just 2600 with 64MB memory.An access filter was implemented for this via the config below. ip as-path access-list...
I have two router connected over a 2 meg frame relay running EIGRP over GRE tunnels.I have two routers for backup using ISDN (2 meg).I have setup waited static route on the ISDN router (wait of 250) to bring up the backup ISDN interface if I loose th...
Hi, i had install native IOS on (access switch)& hybrid IOS on (distribution switch)both are connected with fibre.now i want to configure PVLAN on native IOS.well in hybrid i can do it.can any one suggest how can i go ahead to configure PVLAN.both ...
HiI woold like to manage Unix based system via the Console port ( SERIAL PORTS RS232). I have Cisco 2509 TS and would like to connect the Unix servers to the Cisco 2509 TS so that i can reach the systems directly via the Serial Port. 1- Hase anybody ...
Hello:Segmented our LAN 10.0.1.x and 10.0.2.x with a 3660 in the middle running IOS 12. something.Mixture of NT and Linux boxes both sides.Since the segmentation, we cannot ftp from 10.0.2.x into the 1.x NT ftp server with any linux boxes. We can how...
Hi,I have switch A and switch B and a server with 2Nic's, once connected to switch A and once connected to switch B. Is it possible to configure load balancing?If so, what will I have to configure?Is there a documentation about this?RegardsPeter
Hi AllI have 1 2612 with a tokenring lan on one side and a ethernet on the other side. I have tried to follow several examples from the cisco site without any sucsess. Can anyone help me? This is my config so far, what am I missing here?no service si...
I have a vlan firewalled by a pix. The pix is the default gateway.I will need to route between two private IP address spaces. Can I connect a router with igrp enabled, for example, but not configured as the default gateway? Is proxy arp on the rou...
Does anyone have any experience of the following problem:We recently changed the router-id of OSPF router A from x to y.Router A had 6 neighbours. 3 via ATM point to point links (all in area 0) and 3 via braodcast networks (one of the broadcast links...
Hi,when I insert a GBIC in a 16-port Gigabit module I get the following messages:2003 Nov 15 05:55:50 PST -08:00 %SYS-3-PORT_GBICNOTSUPP:Port 2/11 gbic not supported2003 Nov 15 05:55:50 PST -08:00 %SYS-3-PORT_GBICBADEEPROM:Port 2/11 bad gbic eeprom c...
