Is dcef supported at all on a 6509 hybrid system. I was interested in the WS-X6516-GE-TX module. To enable DCEF, WS-F6K-DFC needs to be added. However, it appears WS-F6K-DFC is not supported on a hybrid system. Is there any alternatives?
Hello,how I realize a redundancy with 2 Switchen?I have 2 catalyst 3550 (EMI) and would like to append other Switche to it.It isn't always Cisco switche but also 3 Com and others.I would like to produce with each of the other Switche with a one cable...
I have a new catalyst 4006 with super engine III WS-X4014. and WS-X4148-RJ45V inline power card.The Rom version on super engineIII is 12.1(12r)EWI want to boot from bootflash with CatOS version 7.6.1, doesn't work. I also download the Rom upgrade v...
Dear All,We are connected to 30 places thru leased line .Now i wanted to configure ISDN as AutoBackup.Now problem is here.If I am configuring place A bri port as a backup of leased line ( it will dial B )then it goes in standby mode.and B will dial ...
Hi,We need to connect 2 Cisco Routers Back-Back using Serial Interfaces. My question is regarding the Cables needed. We already have a "Male DTE" Cable. Should we connect this cable to a "Female DCE Cable" OR "Female DTE Cable" ?Regards \\ Naman
I currently have service guard for HP that moves a particular package (ie my syslog server) to another server in case of emergency. however, when it moves to a new server, my devices cannot communicate to it because the switch (cisco 4006) still has...
I want to log into a remote router and be able to tell if the csu/dsu is internal or external.I thought if I enter this command show service-module serial 0/0 that it could tell me for sure.But does anybody know what command or what I look for to det...
Where would you suggest putting the GRE tunnel source on a router that is NATing? the IP NAT OUTSIDE interface as the source or the IP NAT INSIDE interface as the source? Just wondering because both work. Is there a proper way? Thanks for your input!
have a 3745 with the 36-port Ethernet module in it to provide inline power and connectivity for IP phones. I am having trouble getting everything to play nicely, specifically inter-VLAN routing and DHCP on the 3745. If I setup the router with sub-in...
Hi,The RME Inventory-Chassis Slot Detail does not show slot details for Catalyst 4506 as it is shown below:Total Devices: 1 Cisco Router Number of Router devices = 1Cisco Router Device Name Total Slots Available Slots Location User Field1 User Fi...
Where can I find documentation on how much resources Syslog and SNMP traps use on on a switch. Recomendations for polling intervals Syslog settings, SNMP settings etc. I am looking to implement Syslog and SNMP traps through Ciscoworks 2000 and DFM....
I am configuring DFM 1.1 on my network and want am a little unclear on my switch setup. Currently I have snmp enabled and snmp traps sent to DFM on por 162 and DFM listening on port 162. I do not have any snmp traps types set however and am not sur...
I have an existing WAN network that has been in production and working for over two years.In a isolated part of the network there are three routers connected via Ethernet on a 2900 series router. Each of the routers has a serial connection to a diff...
Will there be any differences in ping times in the following scenarios?1. PPPoA (ADSL-over-POTS USB modem)2. PPPoA (ADSL-over-POTS ETH modem)3. PPPoA (ADSL-over-ISDN USB modem)4. PPPoA (ADSL-over-ISDN ETH modem)5. PPPoE (ADSL-over-POTS USB modem)6. P...
