Hello, Does anyone know the optimal transfer rate for NT servers with gigabit ethernet card on cat6509 switch?
Hello, Does anyone know the optimal transfer rate for NT servers with gigabit ethernet card on cat6509 switch?
we are facing in following problems :1. Logged in users is not showing any user list2. TACACS+ Accounting is not workingWe have installed TACACS+ (ACS version 3.0) Installed on NT 4.00 (Build 1381) Service pack 6 (128 bit high encryption)Internet Exp...
I have a customer using Rumba TN3270 terminal emulation on remote clients communicating with an AS400 via IP over a dialup ISDN connection. This works very well, however, if a session is established the user logs in and leaves the session idle, when ...
Hi people,Bit of background, we have a couple of 1720 routers going in to service a new frame network. Id like to see if I can test the 2 routers prior to them going out into the field. I was hoping to test them back to back using the x.21 serial con...
Connected to 4908G-L3 are two 3524XL switches with fiber jumpers.Connectivity is sporadic. Sometimes both are connected, sometimes just one or the other end is connected. Routing has never occured. We have configured port-channel subinterfaces, enca...
I just recently took over a network that is wireless between sites, 8 sites total. Before the previous admin left he told me WEP was not enabled on the local access points but Cisco Encryption on the routers was. My question is how can I confirm that...
Can you store syslog messages in CiscoWorks for longer then 7 days?
We have a frame-relay PVC between 7506 in Main Office and 3660 in Branch Office with CIR of 1Mb. PVC utilization sometimes overcome CIR. We are testing frame relay payload compression with FRF9 standard to optimize PVC utilization.Well, We have confi...
Dear Sir!Cisco write, that CDP works over FrameRelay (as SNAP-capable link).But however hard I may try, but I can't see Frame Relay switch by CDP in my lab!What CDP configuration must I use on my FrameRelay switch?Best regards, Nick
Hello, We are trialling a internet access Satellite for BT. We have attached our own 1700 router to the Gilat Sat box via a cross-over cable and can browse the net over this, albeit very slowly.Tech Support in BT told us to route via the ip p...
System Bootstrap, Version 11.3(2)XA3, PLATFORM SPECIFIC RELEASE SOFTWARE (fc1)Copyright (c) 1998 by cisco Systems, Inc.TAC:Home:SW:IOS:Specials for infoC2600 platform with 16384 Kbytes of main memorydevice does not contain a valid magic numberboot: c...
does anybody know if callback work well between cisco 1700 and a ascend pipeline 50 ?I'm trying to setting up a callback but it doesn't work. what happen is : 1 - the ascend router initiate the call 2 - the cisco router doesn't close the first call i...
Hi.I need to configure compression for Frame-Relay and ISDN links between a Cisco 7500 and non-Cisco devices. I´ve found some information on CCO stating that no compression standard can be applied yet although efforts are being made. Is this right? I...
Dear Sir! Cisco write, that CDP works over FrameRelay (as SNAP-capable link). But however hard I may try, but I can't see Frame Relay switch by CDP in my lab! What CDP configuration must I use on my FrameRelay switch? Best regards, Nick
I want to configure Frame-relay over isdn thru dialup. Can anyone guide me on this. the scenario is as given below:i have client at location A. location A is connected to location B on serial port using Lease line. Location B is connected to locatio...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |