Other Network Architecture Subjects

I'm trying to understand the configs on a 6500 switch. I have a 6509NEBS with dual sup2 + MSFC + PFC. I understand that there is a set based config/software and IOS based config/software. If I telnet into the SC0 port, which config will I see? From t...

Hi I have a Cat 6509( Sup-eng 2 msfc 2 pfc 2),and a Cat 2948G.The 2948G connect to 6509 through GE. I want to know whether I can do this : I limit a 2948G FE port's speed to 5M or 2M?

My network has several different subnets *as accrued by the different branches of the library for which I work*. My situation is this: we have a dmz subnet supplied by a PIX515 firewall, and supported by a catalyst 1900 switch. The firewall has fo...

We are going to have 3 t1's from the same carrier coming in to a cisco 3640 with 3 wic's in it for our internet access.Other than the configuration of ip addresses, etc on the 3 wic's and ethernet interfaces, and 3 default route statements, one for e...

Hi,Just wanted to know where do I apply my access list in the following scenario:I have a Point-to-Point T1 on my Serial0/0 interface that goes to my ISP.I have a Serial0/0.1 subinterface with ip unnumbered.I have a FastEthernet0/0 that connects to m...

when I show vmps statistic in the VMPS client switchit shows that there is "wrong VQP domain"anyone can help?thanks

I'm currently working on implimenting some bandwidth restrictions for a colocation lan. Each colo gets their own vlan, tagged at the switch, terminated in a 4500M+. The separate vlans are then setup as subinterfaces on the 4500. On each subinterfa...

I'm wondering myself about this issue ....When I've a FEC composed of 4 ports...if I apply some changes to one port (Native VLAN, Port Settings,...) to all the other FEC's port will this changed be applied automatically ??? If on the same FEC is dot1...

HiWe would like to use the private Vlan feature to isolate ecommerce server on a segment and avoid buying mutliple nics for the firewall.We have server A for example connected to switch A and server B (backup of A) connected to switch B. Server A and...

Does the basic IP code on the 2948G-L3 support static entries in the CAM table? The command "set" does not appear to exist in config mode. If it is not supported, is it supported in the Advanced IP verion of the code FR2948GL3-IP?Peter

I have encountered an error message in the router 7000." %IP-4-DUPADDR: Duplicate address 10.1.1.80 on Fddi1/0, sourced by 0090.c4b2.fe3b"Does that mean the this MAC 0090.c4b2.fe3b sensed that there is duplication IP address of 10.1.1.80 in the netwo...

How I do to configure is-is, advertise Level-2 Routes (directly connected interface into L1/L2 Router) into Level-1 Routes without than this was announced into L1* 0.0.0.0/0

When using an LX/LH GBIC with 50 micron MMF, do I have to install a mode-conditioning patch cord?If that is the case, what is the ordering number of this patchcord? Only found CAB-GELX-625 for 62.5 micron MMF.

In cabling specs and compliance information under Cabling considerations for GBICs there is a table that specifies cabling distance for a given GBIC model and fiber type. I am having some difficulty finding a definition for the 'modal bandwidth' colu...

I periodically am forced to reboot out NT server that runs our CiscoWorks because a process of CiscoWorks isn't running. For instance this morning ANI server was not running for one reason or another. Has anybody else had issues with processes stop...