Is there a way to setup XP with a VPN to a PIX with an IOS less than 6.0. I tried using the XP client, but what setup do I use on the firewall. Thanks.Jpoulos
Is there a way to setup XP with a VPN to a PIX with an IOS less than 6.0. I tried using the XP client, but what setup do I use on the firewall. Thanks.Jpoulos
Is FRTS and FRF9 stac can be configured on the same router? What I have in mind is s0/0.1 configured with FRTS and s0/0.2 configured with compression.Any idea if this possible?Thanks in advance.
How i can display the link graph on CMS ?
I am looking for configuration standards that deal with ICMP services on a router. I am wanting to block some ICMP services while allowing those that are dependant. Does amyone have any knowledge or best practices for implementing this?Thanks in adva...
We have a client with two sites (Both ADSL), with a tunnel running between them.The links are used for both Internet traffic and Inter-office (Tunnel) traffic - Is it possible to give the tunnel traffic a higher priority than Internet traffic?Regards...
Hi,I read that 3600 is usually used for let's say larger branch office do access the central office via 6000 concentrator for example, but my question is: is it possible to make the 3600 act as a DSL concentrator, meaning is there way to accept sever...
Does anyone know if I can use regular SSH instead of telnet for remote connections to my 3600?Thanks,Josh
HiI am currently upgrading the 2900xl switches to c2900xl-c3h2s-mz.120-5.WC3.bin to cover snmp vunerabilities. The problem I have come up against is the html access. What I have been doing is deleteing the existing bin file and replacing it with the ...
When we connect pc directly to Switch 6509 we are not able to ping after few days .But after changing the ip address it starts working and the same ip address works on different PC.
Hello all,I have a question about ACLs. When I do a "sh access-list xxx" on my Cisco 6500, I don't see a match next to the access line altough I just made one. Could it come from the fact that it is a port filtering (access-list permit tcp host xxx.x...
I have a Cat5500 with an integrated RSM, performing interVLAN routing for about 20 Vlans (3 of which are populated with about 500 wks on each). The CPU sits at around 10-30% most of the time, but occasionally shoots up to 80-100%. On doing a show pro...
Hi,Anyone know of dial probs between these two platforms? Don't know the Ascend platform but I can find out easily enough if necessary.Dialing from the Ascend to the the 801/1600 with WIC1-B-S/T is fine but from the Cisco kit to the Ascend is not pla...
I have faced alot of input error with abort #. I did change the cable but the error still occurs. Can the Cisco 2611 router configure the "invert txclock" to compensates for phase shifts between the data and clock signals without relying to the DSU. ...
HY I try to install ip ospf demand circuit over ISDN, but the Hellos are not supressed, as soon the main link goes down , the isdn doesn`t come up. When i do it manualy i dont get any neighbor through this link. My interface is set to p-to-p, but i a...
can anyone explain to me (or point me to some links) about the effects of masking 255.255.255.255 in the command, ip route destination_ip 255.255.255.255 next_hop_ip.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |