I have a new branch office with an internet connection and a P2P/MOE back to our main office. I want the internet traffic at the branch to go out our internet connection at the branch but also use the main office internet as a backup. Is something ...
Forum Posts
Hi everyone I am using GNS3 which has shown so much varied behavior for PIM, I have no idea what else to believe, so here is my question . Please consider the following set up: Above we are using SPARSE-DENSE MODE on R3/R4, R4 is RP ( 34.34.34....
BGP configuration having no problem .
Our MPLS provider asked us to peer on vlan 4094 using a /30. Now, silly me put in vlan 4096 by mistake. Traffic still flows though. Is there likely to be any side effects of this eg latency, packet loss etc?
I am having some dificulties with my terminal server:1#sho verCisco Internetwork Operating System Software IOS (tm) 2500 Software (C2500-I-L), Version 12.1(27b), RELEASE SOFTWARE (fc1)Copyright (c) 1986-2005 by cisco Systems, Inc.Compiled Tue 16-Aug-...
Hi, I have a pair of NX7Ks which are connected via a vPC and want to know if I can connect an ASA5585 to each switch using a L3 port-channel? Does the ASA5585 support this configuration? Thanks!
when i tried to ping the destination it is showing TTL expire in transit. and when i do tracert loop is occurring between the 2 devices... i have tried with ping -i 255 but no luck. can any one please suggest me how to troubleshoot the issue...
Hi,I've set up a simulation to do some testing with BGP/EIGRP, see attached. In this network BGP and EIGRP are configured and BGP routes are redistributed into EIGRP.What I want to know is how I can alter the routing configuration so the preferred pa...
Is this possible? Can i do a tcp dump on specified traffic on an ASR? If so can someone direct me to the commands please? Otherwise I'm calling TAC on Monday...
Hello, I have a cisco 892 with default configuration. I'm trying to set this up between our ISP router and a link balancer. The ISP router has an IP of xxx.xxx.xxx.49/30 so the WAN interface on my 892 would be xxx.xxx.xxx.50/30 with access to the x...
Resolved! RPF check and default route
Hi everyone, Hope all my friends are doing great. This is what I see: RP (200.200.200.2)--------200.200.200.20 PIM ROUTER--SOURCE ( 199.199.199.10) RP has 0/0 pointed to 200.200.200.20 When RP receives a Register message ,and source IP of the...
I'm hoping someone can give me some guidance on our possible design. We are going to be running a csr1000v as our edge router. We also are running BGP with 2 ISP's. I've been asked to create 2 vrf's, 1 for Inside and 1 for the Internet. The Inside vr...
Hello, i have planned that i build up the Cisco RV340 with failover LTE modem. Can you give me the supported LTE(4G) modem for this router? I'm in Germany and my mobile provider is Telekom and/or Vodafone. The best thing if i can connect an exter...
Hi guys.... Here is a challenge that migh not be possible but we never know.... In the attached topology.... Let's say that R5 in AS 5 must go via R2 to reach AS 1 ... so R5 > R3 > R4 > R2 is the path to do it.... In normal situation , to influence...
hi folks, after been waiting for a while finally I'm ready to have BGP with my 2 ISP's...right now I have this configured on my ASR: router bgp 2625 bgp log-neighbor-changes network 170.X.X0.0 mask 255.255.252.0 neighbor 208.Y.Y.181 remote-as 35498 n...
