Resolved! How to get logs in ASR 9k
Hi,Can you please let me know that how we can check the BGP, sub-interface and VRF logs in ASR 9k router.Also where the logs gets stored and how can these logs can be copied to remote location.Thanks in advance.
Forum Posts
TOC-BP-SWa#sh ip bgp neighbors 10.14.0.3 advertised-routesBGP table version is 1674320, local router ID is 10.14.0.1Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, S StaleOrigin codes: i - IGP, e - EGP, ? ...
Hi guys. I've just installed card C6800-32P10G in my 6506 with 2T supervisor: But I noticed, that only L2 traffic could be operated via this card and any L3 traffic couldn't. I made a lab enviroment: I connected a PC(10.52.201.201/24) directly to th...
Hey guys, Could anyone explain the difference between autoroute and forwarding adjacency, please? and what would be the use case for both?
Resolved! [ncs540] Please explain IPSLA
Hello, I'm curious about the technology of ipsla Please refer to the config below and explain it.configure terminal !ipslarespondertwamp-light test-session 3local-ip 198.18.57.84 local-port 13000 remote-ip 198.18.57.254 remote-port 13001 vrf default!...
Dear Cisco Community ,Hope everyone is well. Reaching out to ask your expertise with regards to this scenario.Two sites: Main branch and Remote branch. Two firewall in the environment, FW01 serving as default route for all LAN traffic (VPN tunnel cl...
Resolved! [ncs540] Please explain slow-tracking
I wonder what kind of slow-tracking technology is used by ncs540 Below is an example. Please refer to it when explainingconfigure terminal !ptpservo-slow-tracking 16!show configuration!commit
I have the following network (see attachment):Router's interfaces:Interface IP-Address OK? Method Status ProtocolGigabitEthernet0 unassigned YES NVRAM administratively down downFastEthernet0 ...
Hi,I have configured a small topology with 2 x RTRs and 2 x SWs and have 2 ISPs and have configured HSRP for failover. I have connected ISP 1 to RTR 1 and ISP 2 to RTR 2, now vlan 10(ISP 1) that is for ISP 1 is working perfectly fine in SW 1 while no...
This is my current setup (see attachment): There are 3 VLANs: VLAN 1 (management) 192.168.0.0/24 where all network devices live (router, AD server, switches) VLAN 10 192.168.1.0/24 : where PC1 and PC2 live VLAN 20 192.168.2.0/24 : where PC3 and P...
Resolved! Desactivar BGP address family
hola comunidad, aplique por error el siguiente comando en mi ASR1002 (Cisco IOS XE Software, Version 16.05.01b) "neighbor 10.99.2.18 activate" y me cambio la vista en la saluda del comando "sh run", de tal manera que no muesta los prefix-list ni los ...
Resolved! License of C8300
Hi, I'm preparing C8300-1N1S-6T BOM to replace 3954-VSEC-K9 router. It has Cisco 3945E Voice Sec Bundle, PVDM3-64, UC&SEC Lic,FL-CUBE10 I'm bit confused as how to VSEC license for C8300 router? Do i need to add DNA-P-T2-A-3Y license of L-DNA-C8300 l...
Hello.If there exists no explicitly configured EIGRP router-ID, and also there exists no loopback interface...... will the device's EIGRP router-ID advertised to a neighbor instantly change to the loopback interface, or must some reset command (or re...
Hi everyone, I'm experiencing a very frustrating problem with route redistribution from eBGP into OSPF. Consider the below diagram. The goal is to route traffic as directly as possible to the Azure networks 10.24.0.0/16 and 10.25.0.0/16. This was all...
Hello. I am learning CCNA. I am creating a test environment. I have a few questions regarding this Verizon internet router.Usually when we connect to the home router it gives the private network however when i connect this Verizon router it shows the...
