Hello,I'm using a CBS350-48T-4G, and i want to get by snmp the cpu and ram usage on it. but i can't find the correct oid to get those informations. Is it even available?
Hello,I'm using a CBS350-48T-4G, and i want to get by snmp the cpu and ram usage on it. but i can't find the correct oid to get those informations. Is it even available?
I'm replacing an old edge device with two Cisco 8300 routers; Dual ISP setup. The 8300 routers were also ordered with 4 port LAN modules. I'm putting together the config before the routers have arrived and want to figure out the down stream config. ...
Hello. Our spoke ISP failed for 4 minutes. Once it returned, our C2921 DMVPN spoke remained in the NHRP state (no production traffic flowed from this spoke to the hub. This was remediated by shutting then no-shutting the spoke tunnel interface (It wa...
Hi guys,I noticed that from last week, I am getting practically every minute or less, a log message like this in ASR log:Jul 26 2023 14:26:46.158: %IOSXE-5-PLATFORM: F0: cpp_cp: QFP:0.1 Thread:199 TS:00084795299536916500 %PUNT_INJECT-5-DROP_PUNT_CAUS...
Hello! I recently upgrade an ASR 9901 from version 7.3.2 to version 7.5.2, the version was installed, but when issue the command show install active from admin I do not see the same information, do you know what is the problem. Please help me to figu...
Hi! I have an overlapping problem. Router 1 - on g0/0/0 has ip add 192.168.1.1/16 and on g0/0/1 I want to choose the 192.168.0.1/24 ip add. Here is the overlap. It is possible to keep the /16 subnet mask? What is the solution?
I have a router cisco 4331. Today it rebooted abnormally. I checked the log and got the following results:*Jul 26 02:41:21.290: %IOSXE-0-PLATFORM: R0/0: kernel: mce: [Hardware Error]: CPU 0: Machine Check: 0 Bank 5: d400048000900090*Jul 26 02:41:21.2...
In an environment with multiple routers of the ISR 4000 series (ISR 4451-X specifically), some are running IOS XE 16.6.9 and some are running the old version 3.16. Since we have the IOS binary for 16.6.9, I want to load this image onto all routers so...
I having an issue with SFPs with my Cisco router, the SFP should be compatible with the router as they are SFP1G-LX-31 *CO.R2#sh interfaces gigabitEthernet 0/1GigabitEthernet0/1 is administratively down, line protocol is downHardware is PQ3_TSEC, add...
I relatively new to routers and how they work and I've been struggling with this for a while. I have Cisco 4331 router and I want to access my web server via the public IP address on my internal network. The local server I am attempting to access h...
Hello everbody,On site, There is a Relay (like ABB REF615) and they have G.703 port but I can not assign IP to these ports.. They have just a bandwidht. I want to communicate them each other on router with G.703 card. Is it possible? Is there any s...
Hi, I've had a look around and can't seem to find my answer so here goes. Long story short but with a C1111-8P is it possible to have ports Gi0/0/0 and/or Gi0/0/1 act as switchports, or be bridged to the switchports on the C1111-8P. Reason for asking...
Hi,I have a Cisco ASA with a remote VPN to a Cisco router.It seems the tunnel only comes up if I ping the remote router from the inside LAN of the ASA then both sides can ping each other. However if for example the VPN tunnel is down and I ping from...
We're using ASR1001-X with universalk9.16.09.05 version. When I was trying to find the next hop with a pair of src-dst-ip and port to evaluate the load sharing algorithm with the command "show ip cef exact-route src-ip dst-ip dest-port 443 " and got...
I believe I am coming up against this bug: https://bst.cisco.com/bugsearch/bug/CSCvo31022. I do not have DHCP snooping turned on and I as far as I have read it is disabled by default.When I debug ip udp: *Jul 20 2023 21:21:55.271: UDP: rcvd src=0.0.0...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-23-2024 06:56 PM | ||
08-07-2024 10:40 AM | ||
07-15-2024 05:07 AM | ||
07-13-2024 09:04 AM | ||
07-09-2024 05:41 AM |
User | Count |
---|---|
12 | |
11 | |
6 | |
4 | |
3 |