Hi all! I configured the summary-address 172.18.0.0 255.255.0.0 command in the OSPF process on an OSPF ASBR router to summarize the routes that redistributed from EIGRP and found out the type of that summaries route is type O in the routing table ...
Forum Posts
Resolved! BGP 4-byte ASN
I want to run a routing protocols BGP 4-byte. Enable it at device C3750 however i found that it was not compatible/support for BGP 4-byte.Any devices below that can support BGP 4-byte1) C38502) C36503) ENCS 5408/K9
Hi Team,Could you explain frequency Synchronization. Flags: > - Up D - Down S - Assigned for selectiond - SSM Disabled x - Peer timed out i - Init states - Output squelchedFl Interface QLrcv QLuse Pri QLsnd Output driven by==== ======================...
Environment:Cisco IOS Software, s2t54 Software (s2t54-ADVENTERPRISEK9-M), Version 15.5(1)SY10, RELEASE SOFTWARE (fc1)cisco WS-C6506-E (M8572) x2 in vss mode.I configured a DHCP server in the switch , configuration is below:====sw001#show run | secti...
Resolved! MPLS-TE cisco
Helloi want to know in which case, we will configure MPLS-TE in device IOS XR or IOS XE in the backbone ?it is mandatory ? i wait a reply fom expert SPThanks
Resolved! Help with GRE tunnel, P2P with loopbacks
I am new to networking, any help would be greatly appreciated!! I have been searching for hours and can't fix this for the life of me. Thanks for reading/helping. It is point-to-point routers that must have GRE tunneling between them. This is a simil...
We have a Cisco ISR4321/K9 (v16.12.2s) in our lab. I noticed the following image on the management dashboard of the ISR.We are collecting netflow from this system. Nbarv2 is enabled. Our goal is to collect the data above via telemetry. We checked the...
Hello guys, I have two ISP and I want to know what configuration to make load balance between them on cisco router
Hello, I have a network topology which will be shown below. Two routers R1 and R4 are connected via Serial ports. The routers will be configured below. My question is why when I build the routing table for R1 (show ip route), in the last two lines I ...
i am deploying a new CISCO ISR4221/K9 router at customers place, i have unpacked a new router but the router is starting into ROMMON Mode, below is the message displayed on router, please help to resolve the issue: Current Image running: Boot ROM0..%...
This is going to be complicated!!! Thanks in advance for any help you can provide. There are several goals within my request for assistance.I am trying to set up Internet service provider failover on my Cisco C2901 router running IOS 15.7(3)M5. I hav...
I currently have a PPPoE Client connection on a subinterface, which works fine, but since I need to tie in another interace to it, I would like to change it to a BDI. Changed the configuration but the PPPoE client won't come up again. Checked config...
Hi,I'm noticing some odd behaviour with regard to a transit area and it not conforming to RFC2328 on the network below: I have a virtual link between R1 and R2, which works, but R1 seems to be advertising a Summary LSA into Area 1 for the network bet...
Hello, I need to add a route-map to an existing ospf redistribution to filter default and summary routes. Can you please verify my configs below and confirm it would work? Current config : !address-family ipv4 vrf corp redistribute connected redist...
Hi!Please help me, where am I wrong?I don't receice on BUH03 routes from BUH02 and on BUH02 routes from BUH03.I attached a map photo. BUH03router ospf 2 vrf REGredistribute bgp 100 subnetsnetwork 172.16.51.0 0.0.0.255 area 0!router ospf 1network 10.0...
