Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Trouble Configuring Policing

Hi.  I've been trying to get policing to work in my environment, but to no avail.  For the sake of context, I'll decribe my network.  I have 1 50MB Synchronous WAN connection that is shared among the various VLANs of my facility.  I have 5 VLANs: COR...

cisco 3845-hsec-k9

Dear Sir,I am having cisco 3845-HSEC-K9 router now i want to use channalised E1 and Gigabit Ethernet module.iam confusing to find out the module which will be suitable for E1 and Gigeth.any one please tell me the suitable module.Thanks & RegardsSrini...

BGP outbound path selection

I  multi homed to dual ISPs using a single 6509e. Currently, I am only receiving a default from wash ISP and marking one with a higher local pref. most of my traffic flow is inbound, so this config meets my need. The issue I have: if either ISP has h...

bmarms by • Level 1
  • 1760 Views
  • 3 replies
  • 0 Helpful votes

Cisco PIX 8.0 VPN RA with internal NAT

Hi all,All what I'm describing is made with a Cisco PIX Security Appliance Software Version 8.0(4)28. I'm trying to give access to an internally NATed system for VPN RA users.Basically, they open an IPSec session and are hosted in a first subnet (172...

Resolved! Static Routes with Multiple Hops

Hey All, I'm learning about static routes now and just cant seem to "see" it when it comes to routing through multiple hops.  I get it when routing network to network (1 to 2 hops), but if there is a 3rd router to travel through in there, I can never...

tommydubs by • Level 1
  • 12899 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Eigrp Route Manipulation

Hi Experts,I have Scenario as attached, N below is the description1) Eigrp 100 in on WAN cloud.2) Eigrp 10 is on internal Network at Head office.3) I am Redistributing Eigrp 100 in Eigrp 10 at R1 & R24) Redistribution metric on R1 is kept low than R2...

10 Gig EIGRP metric

I have recently connected a 10 Gig connection from the local telco between two sites on 6509's. These two sites also have a 1 Gig links between them. When I connected the 10 Gig link I expected the 10 gig link to be the preferred route, but after l...

Resolved! I have no 'ip routing command'

                   I have seen on the core switch I am working on currently there is not the 'ip routing' statement. HOSTNAME#show verCisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-ENTSERVICESK9-M), Version 12.2(54)SG1, RELEASE SOFTWAR...

Cisco 7600 high CPU utilization due to interrupt

Dear Sirs!We have next router:spb-bg3#sh inventoryNAME: "CISCO7604", DESCR: "Cisco Systems Cisco 7600 4-slot Chassis System"PID: CISCO7604         , VID: V01, SN: FOX1523H7E8NAME: "CLK-7600 1", DESCR: "OSR-7600 Clock FRU 1"PID: CLK-7600         , VID...

NAPT overload on SmartEdge

Hello. Please help me with SmartEdge 100. I have 1 "white" global ip adress.How config NAPT overload for give internet access to that network 192.168.1.0/24.In cisco: ip nat inside source list ACSLIST interface GLOBALINT overloadHOW do this method in...

paktusin0 by • Level 1
  • 748 Views
  • 0 replies
  • 0 Helpful votes

IP Nat conflict question

Greetings,I have a question regarding ip nat inside command which may explain an issue i am facing with a client..Suppose we have:ip nat inside source list 101 interface Dialer1 overloadip nat inside source static 10.0.0.250 87.202.212.131 route-map ...

nemiath76 by • Level 1
  • 1799 Views
  • 2 replies
  • 0 Helpful votes

Resolved! VTP Pruning question

Hi,I'm doing a VTP pruning experiment using  the following network structure in PT, unfortunately it's not available. And I think 'switchport trunk allowed' command is not an alternative since it will yield different results. Scenario:      -vtp prun...

Load more