Showing results for 
Search instead for 
Did you mean: 

Don't miss this Cisco Catalyst 8000 offer


Forum Posts

Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...

translator.png Asolution.png htlm-source.png insertcode(1).png
Kelli Glass by Community Manager
  • 7 replies
  • 16 Helpful votes

I am trying to configure an auto-failover of a location with a primary MPLS circuit/router, with a second cisco router with an IPSec tunnel.  The backup router is up, the tunnel is up, but I've refrained from having a LAN connection made to this poin...

ddalessa by Level 1
  • 1 replies
  • 0 Helpful votes

Hi AllHope you guys can assist, as I am strugging to get a working solution for the below...Scenario: (Diagram attached)We have a MWR2941 (running 12.4(20)MR) router on site A and one in site B which will be connected over a Service provider L2VPN Et...

siddiqirf by Level 1
  • 2 replies
  • 0 Helpful votes

Hello,in last days I'm having problems with a Cisco 1812 device.It works for some time but then crashes and gives the same info:%Software-forced reloadPreparing to dump core... 04:09:41 CDT Wed Aug 8 2012: Unexpected exception to CPU: vector 1500, PC...

Vedran987 by Level 1
  • 6 replies
  • 0 Helpful votes

Hello Everybody,I´m a new in a routing environement particulary for PBR mechanisme :here is the scenario :i have one RT connecting to 2 ISP :ISP1 : GigabitEthernet0/0 description LINK-TO-LAN(ASA) ip address 1...

Company X has private AS number 65000 has two Serviec provider A & B has Public AS number. Is it possible Company X can advertise their e-comm network E-bgp Active and passive mode without having public AS number?Please provide cisco best practice fo...

I work for an ISP and we are currently bonding 5x 6Mb ADSL connections for use as a wireless backhaul.  We are currently using a Cisco 3725 and bonding the links via MLPPP.  This set up is working fine except that we are not getting the full 30Mb on ...

Hi all,I'm currently designing for a customer a new MAN. There are two different Layer 2 domaines as the MAN backbone (area 0) from the provider.My question:Is it a good practice to configure each of the l2 domaines with a subnet and connect these on...

Hi allI have seen the command bgp soft reconfiguration inbound and outbound,can anyone explain what this command does? I have read up but cant understand how it works, also what does the inbound and outbound do ?cheersCarl

Guys,What can i do concerning this error?P00-7800-01#sh env SYS PS1 is present.        Fan status: Normal        Input Voltage status: Normal        DC Output Voltage status: Normal        Type: AC        Thermal status: Normal SYS PS2 is present.   ...

Dear Alli want to access internet throught the cisco 5505here is the case: Outside internface : interface : interface 2 : Default gateway : i want the inside interface 1 :   > ...

Hi, All:Just a quick Q. A router does not install a BGP route in the routing table when the next-hop is 'inaccessible' (will be marked as that on show ip bgp x.x.x.x command) or rather there is basically no route towards that next-hop.Is this the ONL...

Hi,I am in the Lab playing with VRF, got it to work when the switchport itself is a no switchport with IP address, however if I stick the Wan connecting interface into a vlan EIGRP wont create a Neighborship though I can ping it under that VRF.interf...

ktwaddell by Level 1
  • 12 replies
  • 0 Helpful votes

Hi . help me with tips please. I have an Ipsec vpn established between 2 routers cisco 881 :sho crypto isakmp saIPv4 Crypto ISAKMP SAdst src state conn-id status192.168.15.1 QM_IDLE 2001 ACTIVEL_R#sho crypto engine conn activeCrypto Engi...