Hi,I want to redistribute the static routes to EIGRP with customized matric based on ipsla tacking. As the NCS configuration pattern is little different from normal ISR/ASR. Can anyone share a sample? Or validate my draft. ipslaoperation 230 type icm...
Forum Posts
Resolved! Routing based on source subnet
I need to route 2 networks through 4431 out separate interfaces. I currently have a default route - ip route 0.0.0.0 0.0.0.0 10.50.0.9 (G0/0/0) Now, I need VLAN 50 traffic to route to G0/0/2 specifically. !interface GigabitEthernet0/0/0ip address 10...
Resolved! Redistribute Static Route
Hello.If we have some static routes example we have 10, then how we can redistribute 4 of 10 static route to ospf?
Equipment: 871 routerIOS version: 12.4(22)TGiven the following mGRE VTI configuration:interface Tunnel1 bandwidth 1544 ip address 192.168.99.1 255.255.255.0 no ip redirects ip nhrp map 192.168.99.2 169.254.0.2 ip nhrp map multicast 169.254.0.2 ip nhr...
Hello,we are planning to implement active active links between our 2 Data Centers. currently we have 1 link and we use BGP for connecting between the DC's. Now we got second circuit and want to make this as active active connection so that if the pri...
Resolved! Unable to Ping through 2901 router
I'm unable to get my ping through this router, any idea why?
Hello,Someone know how to Set Route preference from two same redistributed routes from BGP through different vrfs.I have two ISPs and learning default route from them. I want ISP1's default route choose as a priority. I am having two vrfs for them 1)...
Resolved! ROMMON version for ISR 4331 Router
Hello experts !! I recently got a used ISR 4331 and I am trying to upgrade the ROMMON. The latest version of ROMMON on Cisco's portal is Release 16.12(2r). However when I type the "show platform" command on my router. It displays that it's R0 version...
Hello.On an ASA 1120 I'm troubleshooting a failing L2L VPN turn-on. The remote engineer requests I run a traceroute to his device. When I try this I experience error "no route to host."This doesn't make sense to me because during troubleshoot it is t...
Hello guys,I have 2 switch nexus 9000, i configure two interfaces like below :interface eth1/1switchportswitchport acess vlan 10no shinterface eth1/2switchportswitchport acess vlan 20no shNow i create and configure the vrf to the interface vlan10 & 2...
Hello,I have Cisco ASA 5525X - 8GB memory, 128GB SSHI want to save the boot image to a USB stick. Could you provide CLI commands to save boot image to USB.Also provide me CLI commands to restore the boot image from USB back to DOM Then I would t...
Dears,We have the throghput problems on 4331 and 4431 and we decided just to buy and activate performance licenses.On 4331 we have already install Performance License which increase from 100 mbps to 300 mbps. The next and the last license type is Boo...
Hello everyone, Here's my topology:I have issue with traffic going to wrong IPSec when trying to use backup link. So the blue squares are communicating with eachother through IPSEC on the pink link that is going through ISP (when MPLS is down, they c...
hello all,i need your support for the next scenarioi have 2 routers and have 2 ISP providers, ISP A, ISP B , how to add HSRP for 2 ISP in my 2 routers ? i mean i already added ISP A configuration in my 2 routers but how to add second ISP B too, thank...
EDIT: Please disregard, the physical layout wasn't correct when I had assumed control of the network. Guess goes to show to always start the troubleshooting at lowest layer. Thank you.Thank you and sorry for the multiple posts- I am normally not the...
