Hi, I just spend a day getting a 1921 with 3G module to work in Singapore on the Singtel 3G network. Finnaly got this to work.Let me know when you run into this, i may be able to help a bit.
Hi,Currently, we have Cisco 2821 and sooner, this device will be refrshed to Cisco 2921.The problem is that we have to copy some files from existing router to new Cisco 2921 router by CF disk.I'm not sure if there is spare slot on both of routers, if...
I have configured multicast (ip pim dense-mode) on two 2911 routers that are connected by a Multilink (3Mbps) Wan connection.The configuration work fine for awhile and sometimes all day but at some point one of the Multilink interfaces stop passing m...
Hi,I need some help configuring DHCP on my WAN interface for my ISP Comcast. Here is my WAN port configuration so far. I am not sure what I am missing but I am not recieving any IP information.interface GigabitEthernet0 description ISP INTERFACE ip a...
I am having problems getting a loopback address to publish through BGP and am hoping someone can lend a hand. This is running on an 1841 router. I have four subinterfaces off of the F0/0 interface, a loopback and serial interface:sh ip int brFa...
Please assist with typical ADSL configuration. My ISP only sends out DNS information automatically (PPP) - no static entries. I need to capture this information and relay it to users via DHCP. Currently when I do "ipconfig/ all" all DNS entries are e...
Hi,I have a Cisco 1841 router connected to two different lines (same ISP) and I would like to load balance between them. I think I have achieved this point, but the problem is that remote VPNs do not work (only from Dialer1).This is my diagram:ISP1...
Hi, I have got Cisco 881 (MPC8300) processor router. It is not supporting EIGRP. I have got License Information for 'c880-data' License Level: advsecurity Type: Permanent Next reboot license Level: advsecurityDoes it support EIGRP or not, whi...
Hello,Is it possible to establish a interface dialer on a layar 3 switch?Or is it only interface for routers?I have a c3750 switch (WS-C3750G-24T), and when i try to establish a dialer interface i get an error message:Switch(config)#interface dialer ...
Hello,I have read today about two-rate policer and would like to know the difference between the following to configurations:policy-map test-map1class test1 police cir 6000000 bc 1125000 pir 12000000 be 2250000 conform-action transmit excee...
Hi All;We have a DC and branch connections over an ISP's MPLS VPN cloud. There are 2911 routers at branches and they are connected to ISP PE routers over BGP (Our ISP only support BGP). And our DC ASR 1002 routers are connected over BGP again. We adv...
Equipments:1. I have 5 workstations with 2 servers but the backup server (black) is shut down intentionally. 2. I have 1 cisco gigabit unmanaged 8 port switch and 1 cisco 1941 vpn router.Scenario:The cisco 1941 vpn router is configured for IPVPN conn...
Hello,I want to learn about HSRP group support and limitations on the Catalyst 4948.But these kinds of following documents is not found.HSRP Group Limitation on Catalyst 3550 FAQhttp://www.cisco.com/en/US/products/hw/switches/ps646/products_qanda_ite...
Hi, Thanks in advanceI am trying to configure QOS shaping based on object-group, however cant get it to work. Can anyone point me to right directionHere is the snipet of configobject-group network admin host 10.1.1.1class-map match...
Cisco 806 router cannot read Flash memeory and boots directly to RomMon. It acts as though there is no Flash installed.Does this router come with 8MB Flash built in?I see I can purchase additional 4MB or 8MB cards for it, but thought there was some p...
