Routing

Has the CGR 2010 been tested beyond 100 hours at 85ºC? If yes, for how long?Operating ConditionsOperating Temperature-40 ºF to 140ºF (-40 to +60ºC) continuous operating temperature range-40 ºF to 185ºF (-40 to +85ºC) type test for 100 hours at 85ºC

Hi all,I have a very common question with respect to T1 links. For a T1 having bandwidth of 1.544 Mbps, the upload and download are 1.544 each. What happens when I download 1.544 Mbps of traffic. Does it affect the upload because already 1.544 Mbps i...

Hi friends,I have this small network comprising of around 40 users complaining about the poor speed. And they have 2900 WAN router having 10M service. The interesting thing is that they are using proxy server for all the communication.I am very new t...

Hello,We have been facing performance issue on a new setup with NAT and OSPF.Basically, the two routers in the middle are NATing the private customer subnet with 2 pools of public IP (one on each router). The outbound traffic is loadbalanced between ...

Hi Guys,Ok i'm new to working with Routers (in the real world) So i have a client who needs to access an internal server to access a web service. The web service should also be available to two ip address's (lets say 198.1.1.1 & 198.1.1.3) The Web Se...

I want to connect Aoffice to Boffice using cisco1800Senario is like this.Aoffice 192.168.169.0/24Boffice 192.168.0.0/24from Aoffice i have connected through 3com BridgeAoffice (Bridge1-192.168.169.254)------>(Bridge2-192.168.169.252)--->CiscoWan port...

can the 5ghz and the 2.4ghz switch place on a cisco AIR-AP1250 ---Posted by WebUser Claus Hove Meow Nielsen

Hi,In a lnux box: ping -s 1472 -M do 8x.xx.xx.xxPING 8x.xx.xx.xx (8x.xx.xx.xx) 1472(1500) bytes of data.1480 bytes from 8x.xx.xx.xx: icmp_seq=1 ttl=61 time=73.9 ms1480 bytes from 8x.xx.xx.xx: icmp_seq=2 ttl=61 time=72.5 msA tcpdump el linux: We could...

Hi,We have recently upgraded our lan network over different sites with cisco routers and switches and icorporated VOIP in it.There are actually sevent sites with EFM internet service.Cisco routers that we use are Cisco 3725 at headquarter and Cisco 1...

Hi,I try to configure a Cisco 3925 with VWIC3-1MFT-G703 for an E1 but the line is still downform my side and from the site of the provider the config below:!controller E1 1/0   channel-group 0 unframed!interface Serial1/0:0   ip address XXXX XXXXWhen...

Hi Guys,Can the ASR1004 RP-1 act like a switch? where i can create SVI,vlans, and switchport mode trunk or access on a particular ethernet interface?i tried to create an SVI but it failed. the IOS-XE im using is "asr1000rp1-adventerprisek9.03.05.00.S...

I am trying to research what Cisco equipment can handle 10 1 gig ports comming into it.... I have heard that some of the Cisco equipment just simply can not handle this capacity.... Is there anyone out there with some real world experience and willin...

Hello to all,I would like to mention that I am a total new comer (NOOB) for Cisco Router. All I know is plug the console cable to a serial port on a PC, fire-up HyperTerminal to view and that's it. I don't know any command or scripts.I am trying to l...

Hi,Please check attached rough diagram.I'm not advertizing 151.41.1.4 anywhere to B,C,D. only router A knows about 151.41.1.4.can I put following static route on D:ip route 151.41.1.4 255.255.255.255 192.168.1.1will above "static route" send all traf...