The 1941 router has USB ports, Will it support a USB celluar data card? Please advise.Thanks,Joe
The 1941 router has USB ports, Will it support a USB celluar data card? Please advise.Thanks,Joe
Sorry if off topic, but what is the best way to cut and paste a configuration into the message? I am losing all CR and the lines are continuous thanks
Is it safe to manage an 891 router across the Internet using Cisco Configuration Professional 2.4? If so, a few pointers on enabling and configuring it would be appreciated. If not, I assume setting up a VPN to the router then using CCP across the ...
We are in process of migrating our entire MPLS connected network from one provider to another. In our datacenter, we have a link to both MPLS networks and will be the gateway between the two until we're fully migrated. We run OSPF between us and each...
I have a system that has everything on the managment network 172.16.1.0 network gateway 172.16.1.1. I have connected to the system a small Buisness router on the same network but with a gateway 172.16.1.70, It connects to another small business route...
Hi,I really need some help when it comes to configuring my new Linksys Cisco WRT120N router to my PPPoE connection. I've visited 192.168.1.1 but I'm not sure what to do next. So, I've got a PPPoE connection, static IP address, Linksys Cisco WRT120N r...
hello all,I am in the process of studying to receive my CCNP. I read some articles on end-to-end and local vlans, basically have this understanding:-End-to-end would allow for a user to cross the core (into the WAN) to contact another user in the sam...
I was attempting to setup our 7204 Cisco router to use RADIUS for authentication via the AAA commands. I must have messed up when configuring it as it comes up via TELNET asking for a username and password but doesn't take my AD credentials. How migh...
I have a network with various remote siteswith dual connections into each (BT is the ISP)The primary link is over an MPLS and work s fine alone using OSPF.The secondary link is an ADSL link using BGP and is redistributed into OSPF using prefix lists ...
HiGRE Over IPSEC is configured on a point-to-point link. What is the maximum bandwidth supported by GRE Tunnel.The point-to-point link is 10MB, can I limit the transmit and receive bandwidth on the GRE Tunnel.The Router is C3845-ADVSECURITYK9-M), Ver...
My company purchased 100Mbps business ethernet. what router would you recommend?
I have two routers in two seperate AS's.RtrA advertises multiple routes via eBGP to RtrB.RtrB will learn these route via eBGP.There is one route that will be learned via eBGP and also OSPF. I know that the eBGP route will be preferred on this router ...
Hey all,I have the following topology:| Router A |------------{ Internet }----------< Firewall performing PAT >----| Router B |Router A has a public IP address facing the internet. Router B has private IP addressing and is being PATed behind a firew...
R1----FRAME RELAY SWITCH----R2 102 102 1.1.1.1 1.1.1.2frame-relay map ip 1.1.1.2/1.1.1.1 102 broadcastI see that when you configure the above command on a serial interface on a router and when we enable eigrp,the ro...
Hi,We have Cisco 3845 and Cisco ASR 1000 Router.In current scenario like that,Internet Link-->Router 3845-->Cisco IPS-->--------Cisco 3750 SW configured with layer 2--------> Cisco ASA active...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-14-2025 01:24 AM | ||
06-06-2025 12:18 PM | ||
05-15-2025 07:28 AM | ||
05-13-2025 03:49 AM | ||
05-12-2025 03:28 PM |
User | Count |
---|---|
10 | |
4 | |
3 | |
3 | |
2 |