Hello, We are preparing to service MetroEthernet internet provided to our POPs over copper lines using VDSL2 technology. I would like to know what Cisco DSLAM products with what scalability options (Max-min ports, slots etc) exist.Thanks
Hello, We are preparing to service MetroEthernet internet provided to our POPs over copper lines using VDSL2 technology. I would like to know what Cisco DSLAM products with what scalability options (Max-min ports, slots etc) exist.Thanks
Hi All,For further study of CCNA and labs I purchased 1760 router. Otherwise working OK but it is not saving running configuration. After changing the running config , I issue the command -->Copy running-config startup-config. It saves. I switch off ...
Hi Champs,I recently configured a username with priviledge level 5 for the below commands. Though everything seems to work fine, the output of "show running-config" only shows up a couple of lines and not the complete config. However "show start" and...
Dear Experts,I want to replace the modem with the attached configuration (file attached: XAVI Modem Config.pdf) with the Cisco HWIC - 4SHDSL,How can I do ?Thanks in advance
Dear Friends, I am not able to figure out the relation between WFQ's parameter HOLD QUEUE and Conversation Value. I put this concept in my Lab and found that "SHOW INTERFACE" command shows both Hold Queue parameter in OUTPUT QUEUE and Conversation pa...
Hi,I have very little idea about QoS.. can any1 help me on configuring QoS with below details.I need to setup L3 QoS for voice with highest priority and rest all traffic with best possible..I have to configure the L2 QoS also for voice traffic as hig...
Hi I have cisco Nexus 7000 switch A and B. I have two cisco Nexus 5000 switch R & T.I have created L3 and L2 vlan in both A and B e.g vlan 32, 41 & 999. SW-A is primary HSRP and Sw-B is secondary. All are permitted between PVC on A & B. I have create...
Dear Guru's,I dont know if this is possible, can i create a community that influence routing on client side based on what its received? Based on the drawing, the client is receiving the prefix on two AS's (AS300 and AS200) but i want the client to pr...
Hi ,Is there a way for route leaking in the MPLS CE?CE1 has Global routing & a VRF named VRF_A. Is it possible to that a single host in Global routing can communicate with VRF_A host or vice a versa?Regards,Santosh
Hi all,We are trying to replace a external adtran (t3su) and HSSI Card with a NM T3 card (with builtin T3SU). When we move the circuit over to NM T3 card from external adtran for some reason it does not see the circuit and interface and controller st...
Hi, Can anybody please suggest how to setup VPN tunnel in Cisco 3825? thanksgaurav
Hi,Sorry to ask this basic quiestion.Kindly help me in understaning the below output.ATM1/0.70 is deleted, line protocol is down ============ATM is Deleted ???? Hardware is ENHANCED ATM PA MTU 4470 bytes, BW 149760 Kbit, DLY 80 usec, re...
Hi, I have sw-A and B connected with trunk mode. My question is can vlan 2 members on Sw-A can communicate with Sw-b hosts having vlan membership vlan-2.ATT- Description of vlan 2 is different on both switches, but vlan ID is sameSw-A->> VTP mode tra...
Hi all,I have C6500's SP VSS and i found very high CPU process on switch no.1. I would like to know what command to show process cpu on switch no.2Thanks
Dear Friends,Kindly I need your valuable help.I have to connect 10 branches to my HQ over MPLS-VPN. The Telco has provided the Link and the configuration, now i have to configure and connect the routers at each 10 offices. I am using static routing a...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-06-2025 06:09 PM | ||
| 10-26-2025 02:24 AM | ||
| 10-24-2025 11:24 AM | ||
| 10-16-2025 11:52 AM | ||
| 10-15-2025 06:33 PM |
| User | Count |
|---|---|
| 4 | |
| 4 | |
| 3 | |
| 3 | |
| 1 |