Resolved! ACL Query
Hi Guys,What is the use of below ACL.access−list 110 permit tcp any any gt 1023 establishedThanks Amolak
Hi Guys,What is the use of below ACL.access−list 110 permit tcp any any gt 1023 establishedThanks Amolak
Hi,can anybody tell me how many pps can support a WIC-1T?
Hi Guys,Is there any difference between below acl entries?access-list 110 permit tcp host 1.1.1.1 gt 1023 host 2.2.2.2 eq 20 establishedaccess-list 110 permit tcp host 1.1.1.1 host 2.2.2.2 eq 21access-list 110 permit tcp host 1.1.1.1 eq 20 host 2.2.2...
Hi Cisco Engineers,I want to take CCNA 640-801 exam but Should I recertify to the new CCNA certification if it's applied....Regards,Ibrahim Alwahidi
Hi,we would like to setup the loopback interface for all routers and we would like those loopback address can be routed. e.g.router A---loopback0192.168.254.1 255.255.255.0router B---loopback0192.168.254.2 255.255.255.0router C---loopback0192.168.2...
Hello,I need help to solve this case, here are the details:Router c3845:interface GigabitEthernet0/0 ip address 212.x.x.106 255.255.255.252!interface GigabitEthernet0/1 ip address 88.x.x.1 255.255.255.192!ip route 0.0.0.0 0.0.0.0.0 g0/0ip route 172....
Hi guyswhen I boot my 1841 router it hangs!!this is console messsegeCisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(1c), RELEASE SOFTWARE (fc1)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2005 by Cisco System...
Dear AllI took the following note from cisco siteWire-speed performance on 3825 with services enabled at up to T3/E3 rates.my quiestion is.does this apply if i use Cisco Gigabit Ethernet Network Module to connect it to my service provider, in other w...
Hello,I have just upgraded to 4.1 and now I am unable to see Tacacs Admin info (When a command is typed it is no longer sent to the ACS server).Here is my AAA config on the router:-aaa new-modelaaa authentication login default group tacacs+ localaaa ...
Hi,How can I monitor any out going connection to internet on interface Ethernet using port 443.I have router 1841.Please helpI did the following ruleaccess-list 106 permit tcp any eq 443 any established logthen on the proper interface ip access-group...
in eigrp between two routers, why there isnot a need for the ospf condition that hello and dead intervals must be the same at the 2 routers????????
how to configure reverse route in router?....help needed urgently
i telnet 2620XM and unable to connect, when i login to console its show " Low on memory; try again later" what to do i am not able to connect both by telnet and console. need urgent replythanx & RegdsNaveed
hi,i have a 7604 router with som gig interfaces.i have some subinterfaces (802.1q) interfaces on the physical interface, which are trunks to other mpls pe router, so i have to do labelswitching.therefore i use the command "mpls mtu 1512".the problem ...
Hi,Let first have the Network Diagram. 1. I?m having Cisco 2821 Router in Head Office which serving 4 Branch Office with Cisco 1721 Router in MPLS VPN Cloud.2. Right now I?m having a Remote Location which is connected using Wimax Technology using Cis...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-13-2024 09:04 AM | ||
07-11-2024 01:54 PM | ||
07-09-2024 05:41 AM | ||
07-03-2024 08:54 PM | ||
07-02-2024 04:20 AM |
User | Count |
---|---|
14 | |
5 | |
4 | |
3 | |
2 |