Hello all, I am trying to upgrade our existing Internet router 3900 to 4331. Scenario: Existing router 3900 has BGP peering with 1 ISP with a default-route, and OSPF neighborship with a Cisco ASA outside interface using our public IP addresses Th...
Forum Posts
Hello. So I had this same discussion on a different forum and had plenty of help but either I simply did not get it or I did not express it well enough to have no resolution. I am posting/attaching a picture as well and hope that it's description ove...
Hello I want to replace me legacy Cisco ISR4351 with APPx license with a newer C8300 platform. I'm being told the newer Cisco C8300 has no support for MPLS or Policy Based Routing. Are there license options available to include APPx supoort needed fo...
Not sure if anyone has come across one that they could point me to? A lengthy or involved WLC packet tracer lab? Not anything basic.
Resolved! NAT Logs does not appear on monitor
Hello Everyone,I'd like to see and catch NAT log in my ASR 1006 and then I ran "ip nat log translations syslog". But NAT log doesn't appear when I check " show log". How can do for that? Here is the Logging command that I've already configure. loggin...
Dear friends, I need to summarize routes from the backbone area to connected areas! The line in the config of the ABR looks like: router ospf 2area 0 range 10.4.0.0 255.255.0.0area 1 range 10.2.0.0 255.255.0.0 The routing table on a router in...
Hi,How can I access host in Inside network via Outside External IP address. It did not work with the normal nat rule (e.g. ip nat inside source static tcp 192.168.1.17 443 20.0.20.23 4443).I need external static IP e.g. 20.0.20.23:4443 -> 192.168.1.1...
Before the upgrade, I was able to SSH into a level 15 user and it would land me directly to # without using enable. After upgrading to from 16.3.8 to 16.9.4, my level 2 account can still SSH in but level 15 user account gets % login invalid. So I try...
Hi, First, I'm not very good with networking let alone Cisco networking and CLI. I have a decent understanding of networking concepts and can navigate but no where close to networking engineering level. I have a site that cannot access https://cfa...
What am I asking? What I am trying to do is make sure that when my device (or preferably router) reboots the client gets the same IP assignment? Why am I asking this? We have had issues getting into the network devices via vpn because the ip ha...
I'm searching for a Visio Stencil, but I was not able to find one for an C1118-8Phttps://www.cisco.com/c/dam/assets/prod/visio/visio/routers-isr-1100.zipAny ideas?
Choose the size of the key modulus in the range of 360 to 2048 for your General Purpose Keys. Choosing a key modulus greater than 512 may take a few minutes. How many bits in the modulus [512]: 2048 % Generating 2048 bit RSA keys, keys will be non-...
Hi everyone, I simply configure f0/0 and ospf on R1 but it is not working. anyone tell me why is it happening?
Switch(config-if)#shut %LINK-5-CHANGED: Interface FastEthernet0/4, changed state to administratively down Switch(config-if)# Switch(config-if)#no shut %LINK-5-CHANGED: Interface FastEthernet0/4, changed state to down Switch(config-if)# Switch(con...
Hi, I am struggling to change the lease times on a router (and also in packet tracer) The command lease 5 30 5 (as an example) just gives an bad command prompt The aim here is an high turnover area of clients in an address pool I want to purge o...
