Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hello all, I have a router that is currently only booting up to rommon mode. It cannot find an image in flash. As such I set up a tftp server on my pc, copied the IOS to the root, and did the tftpdnld from rommon mode.It gets all the way through th...

joneschw1 by Level 1
  • 611 Views
  • 6 replies
  • 0 Helpful votes

Dear support,I am after some advice on the upgrade of two of our 7204VXR routers. These are our perimeter BGP / OSPF routers.They are both running c7200-p-mz.123-9.binCurrently we have 2 x 7204VXR’s each with;NPE400 (256 MB RAM)I/O controller (think ...

aoshea by Level 1
  • 352 Views
  • 2 replies
  • 0 Helpful votes

Hi all,I am looking to configure MLPPP to combine my [2] T1 serial interfaces to my ISP. I have looked a bit on the cisco web site for information on how to do so but to date cannot seem to track down a simple config. My other problem is that each ...

madlm by Level 1
  • 673 Views
  • 4 replies
  • 0 Helpful votes

Resolved! Bridge with VLANs

I will have two sites connected with a T1(see jpg). Is it possible to bridge the two routers creating one subnet? Also can this connection be trunked for vlans?

wmurray by Level 1
  • 669 Views
  • 5 replies
  • 0 Helpful votes

Hellodoes a router(in my case a msfc2) replicate a single mulitcast stream (MC-source is not directed connected) to all Vlans with "ip directed-broadcast" enabled? If yes, will do the msfc this in software and could cause higher cpu?many thanks for h...

Hi,Im redistributing static routes to EIGRP.Is it possible to block the external EIGRP route update?so that other sites will not receive unneccesary routes.If possible,how can i do that?Thanks

rrmpejero by Level 1
  • 429 Views
  • 2 replies
  • 0 Helpful votes

ip route 2.2.2.2 255.255.255.255 1.1.1.1ip route 2.2.2.2 255.255.255.255 1.1.1.5interface e0/0ip address 1.1.1.2 255.255.255.252interface e0/1ip address 1.1.1.6 255.255.255.252interface loopback 0ip address 3.3.3.3 255.255.255.255router bgp 100neigh...

fly by Level 2
  • 588 Views
  • 4 replies
  • 0 Helpful votes

I'm trying to get a route-map on a FWSM to work with a prefix-list, but in the match criteria it does not appear that you can enter in a prefix-list. I can create a prefix-list, but am unable to use it in a route-map.Anyone have any insight as to wh...

rm2017 by Level 1
  • 1247 Views
  • 17 replies
  • 0 Helpful votes

I hope someone can point me in the right direction as I have been staring at this problem for so long I think I may be completely overlooking the obvious. I have the router set up in a router-router VPN tunnel between 2 LANs. It works fine and all t...

When we configure the 2600 router with "router bgp", we noticed an error message "Protocol not in this image" ? Is this related to the current IOS version which does not support BGP ? Any idea ?Cisco Internetwork Operating System SoftwareIOS (tm) C26...

mpabilona by Level 1
  • 2865 Views
  • 5 replies
  • 0 Helpful votes

hallo,I have a new cisco1841 ISR router with WIC-1T and WIC-1-B-S/T-V3, ios 12.4(1a) ip-base.It shows continuosly in console the message:*Jan 3 17:15:35.611 UTC: ASSERTION FAILED: file "../chips/gt96k/gt96k_timer.c", line 771I tried another new cisc...

fsoffia by Level 1
  • 2278 Views
  • 3 replies
  • 0 Helpful votes

Hi all,I have WAN link BW 64Kbps, this rate is transmit 64Kbps and recieve 64Kbps (total 128Kbps) or transmit + recieve is 64 KbpsThanks