Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Webinar

 
Labels

Forum Posts

hello.there is a router run eigrp and ospf, and when redistribute from eigrp to ospf, only route learned from other neighbors, which mean didn't redistribute its own route ( directly connected ), could somebody explain what kind of situation is this ...

ikizoo4 by Level 1
  • 413 Views
  • 3 replies
  • 0 Helpful votes

Hi Gang,Can someone please shed a little light on the following description from a CCO doc, that relates to Ethernet interfaces. What I'm curious about is the "because the carrier was asserted" part. Can anyone enlighten me please? I have assumed th...

I have four T1 configured as MFR via MPLS. See below the config given by Telco.One Point-to-Point sub-interface is used for Internet traffic, while the other one is used for private branch locations. Technically, if one T1 goes down in a bundle, th...

abbas.ali by Level 1
  • 421 Views
  • 2 replies
  • 0 Helpful votes

Is it possible to do source based routing on a 3750 switch? This is my core vlan routing device.Here is the situation. I have a vlan which I want all traffic (including internet) to default to 3725 router, to be shuttled out it's serial port, rathe...

normalit by Level 1
  • 873 Views
  • 2 replies
  • 0 Helpful votes

hello every one. I have bought 2 cisco 2500 routers, I connected them together with dte/dce cable, encapsulation on both serial are hdlc, clock rate on dce end both set to 64000, routing protocol used is rip, every time i enter sh ip route, cannot s...

Please,i configure pix to locate the server on dmz interface and host on inside interface.the problem is that the host on inside interface cannot reach the e-mail server (196.202.232.17).This is show run output:namesaccess-list accl_dmz permit icmp ...

Can anyone tell me how the BGP neighbor fall-over feature works? I'm wondering how it's different from fast-external-fallover.I've read the description here:http://www.cisco.com/en/US/products/ps6350/products_configuration_guide_chapter09186a0080455...

In regexp, how is the underscore used? From Cisco docs it says, _ can be used to replace a comma (,), left brace {, right brace }, ^, $ and space. This is in regards to using regexp in BGP as-path filtering. The objective is to prevent a client peere...

frenzeus by Level 4
  • 1007 Views
  • 4 replies
  • 0 Helpful votes

Hi, I am getting a lot of flushes on a POS interface. Can someone tell me why i am seeing these flushes and how can I fix the problem. thanks show int pos 1/1/0POS1/1/0 is up, line protocol is up Hardware is Packet over Sonet Internet address is ...

Can someone tell me whether there is an IOS command to retrieve the device serial number on a MC3810 router?If not, is there another way to retrieve this besides looking at the back of the router?Show version does not provide this information.Thanks!...

I have a 3660 with an ATM DS3 modules in connecting to an LS1010 that then connects to a 7206 with an ATM DS3 module, I'm trying to do bridging with this configuration. The one is setup as bridge IRB the other RBE. When I hook the 3660 to the 7206 ...

runner by Level 1
  • 587 Views
  • 2 replies
  • 0 Helpful votes

Hellowhen configure ISDN backup floating static route or Backup interface, interesting traffic is configured by "dialer-list" and ACLs. only interesting traffic can triger the ISDN link, but what about after ISDN link active, still those ACL filterin...

ikizoo4 by Level 1
  • 414 Views
  • 3 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card