Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

hi i want to replace cisco 3660 router with cisco 2851 router.. want to know if that is the right choice.This router is a border router with BGP running, average traffic is about 5 mbps both side, it is also running HSRP with other 3660 .The cpu usag...

egain.com by Level 1
  • 1178 Views
  • 2 replies
  • 0 Helpful votes

Hello,I am desiging a solution to provide redundant internet access for a client with (2) T1's to different ISPs. To run the full BGP routing table from each isp, is a 2811 with 512MB of Ram sufficient for this or do I need a router with a faster pr...

I have a router (1720) with serial (nat outside) and isdn (nat outside) as backup. This router is to connect to internet. The router also perform NAT to translate all inside private users to internet.In normal condition, the serial is up all users ar...

wchew by Level 1
  • 1093 Views
  • 6 replies
  • 0 Helpful votes

Hi,I am confused about subnetting - the 128 mask. I am using Boson guides, and they do not use a 128 on a class C. I thought the first address group would translate to this network and the last address group would translate to broadcast, so if you ...

xtech by Level 1
  • 837 Views
  • 3 replies
  • 0 Helpful votes

HiI have 2 serial leased lines bundled using virtual template. I want to apply a QOS Policy to serial interfaces. Where do I apply the QOS Policy? Can I apply to virtual template interface or both the serial interfaces?rgds

Dear all,I have one of my two giga ports on the 3550 in the following state:C3550_Rack06#sh int gig 0/2 GigabitEthernet0/2 is down, line protocol is down (err-disabled) Hardware is Gigabit Ethernet, address is 000e.d712.8532 (bia 000e.d71...

ifabrizio by Level 3
  • 1152 Views
  • 7 replies
  • 0 Helpful votes

using a 3825 with the advanced service image I'm trying to route between different subnets but have been unsuccessful. Does this setup look correct?When I do a sh ip route I never see these route showup. I've tried turning on rip and I've tried sta...

wshall by Level 1
  • 683 Views
  • 1 replies
  • 0 Helpful votes

Hi All,What do I have to enable in order to see this on router 3825?! Last configuration change at 21:30:36 Thu Mar 31 2005! NVRAM config last updated at 21:30:50 Thu Mar 31 2005TIA--Tho Tran --

ttran by Level 1
  • 613 Views
  • 1 replies
  • 0 Helpful votes

Hi,I want to configure Priority Queuing on frame-relay circuit, for example I have configured following PQ,priority-list 4 protocol ip high tcp 8080priority-list 4 protocol ip high tcp 443priority-list 4 protocol ip medium tcp 23priority-list 4 proto...

ccobtn by Level 1
  • 664 Views
  • 3 replies
  • 0 Helpful votes

I have an 837 connected to internet and LAN. The WAN interface receives an IP address via DHCP from the ISP. The LAN is on network 192.168.1.0I want to setup NAT to redirect port 8080 on WAN interface to 192.168.1.250:80 on LAN.Have had a play but ca...

N_Martin by Level 1
  • 763 Views
  • 2 replies
  • 0 Helpful votes

I have to design an OSPF network. The backbone part, area 0, comprise 2 sites linked by a 100 Mbps LAN extension. Both sites has a WAN link to a MPLS/VPN network running BGP: the main site has a 100 Mbps WAN link and the backup site has a 30 Mbps WAN...

bdube by Level 2
  • 616 Views
  • 1 replies
  • 0 Helpful votes