Routing

Currently there are routers and two T1's connected to two different ISP's in a BGP multihomed setup. The IP addressing space belongs to ATT and because of this the ATT T1 seems to see more traffic. One T1 which comes from Global Crossing will be rep...

Hi all, I have a cisco 7200 router with ATM E3 interface, this router is connected to a bpx ( BXM-E3 card),Also I have MGX 8850 with PXM1E card and RPM, I want to configure both trunks and root vpi 1/0 from the ATM router to interface switch 1.1 poin...

Hi Together,i like to use the "ppp chap hostname feature" for Authentication with an Username different than the Routers Name. The first implementations with just one dialer Interface works fine on a Cisco 836.But now i have the Problem that if a rou...

Hey All,What is the best way to disable the autostate-like functionality on the VLAN Interfaces inside a 2801 ISR Router?I would like Interface VLAN 10 to stay up even if all ports in the router go down.Thanks for the Help!-Joe

hi, my cuurent situaution is I have 2 offices with identical setup. 3750---pix515---2621XM--ISPBoth offices need to be conected and I've done this with an IPSec between the Pix's. I am not using any dynamic routing. Now I have a request to add one mo...

Hey All, This one maybe a tough one, I have a friend trying to break protocols across two lines. He wants his IP phone traffic to use a T-1 and his other traffic to use his 10mb wireless. Can you route via tcp and udp ports to one remote subnet?T...

Hello,I have 2621XM router at my site. I got 3 , 2 Mbps links running on the same. I have bundled these 3 links with one common multilink.What I am observing is the router CPU hits upto 100%. every time i bring all these 3 links in production. Now I...

I am planning to upgrade 7206 router currently running a very old version of IOS. I have git an ATM interface that connected to the internet..This router load the IOS from an 8MB flash from slot. What is teh best practice to upgrade it with less down...

Hi cisco gurus.....can anyone explain me what does the command Active Backup interface means....and how is it different from simple backup interface command.Thanks in advance

pl. clarify the following:1. under what situations do we use NM-30DM 2. i have to connect 30 branch offices to one central office. Each branch will have a small router with dial-up port & dial-up modem. At central location i propose to take Channelis...

Hi cisco gurus....I have a framerelay link which has 3 PVCs,can i create another framerelay link having with 3PVCs with each PVC being the backup for the corresponding one......If this is possible how, if not is there any other way to have backup of ...

I think I have a problem with either my router.I can not seem to connect to any ftp sites. I had a power failure a week or so back that out lasted my UPS. Ever since then I have been unable to ftp out. I am not sure if my router has lost some sett...

HiI would like to use two 1760's with single Serial WIC to drive two separate 2Mb/s lines to another pair of 1760's. Behind th 1760's at each are are pairs of 3560 switches.The object is to:1) Have no single point of failure2) Load balance when all t...

Hi all, I have been tasked with installing a small WAN through 3 sites all connected via wireless bridging. Each site has an 831 router and a 2950 switch. Anyway I was wondering how I can go about structuring the IP addressing, can I set up the 831 r...

Dear sir,i want to know, if my downlink is choked and uplink is free. Then due to choked downlink will I get problem in sending mails and sending attachments.Regards,Ashu.