Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Don't miss this Cisco Catalyst 8000 offer

 
Labels

Forum Posts

Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...

translator.png Asolution.png htlm-source.png insertcode(1).png
Kelli Glass by Community Manager
  • 10240 Views
  • 7 replies
  • 16 Helpful votes

Hi, one of the customer wants to configure shaping qos on multiple port at one switch.  As this switch roles HQ distributtion switch to mant branches. (HQ is multicast source) There are multicast stream and the customer wants to allow only 70% bandwi...

hjson0001 by Level 1
  • 412 Views
  • 2 replies
  • 0 Helpful votes

Hello Team,I would like to better understand of behavior of my QoS. I have configured class with priority, and then with police. Lower classes are configured with "bandwidth remaining percent" command.policy-map TRAFFIC-OUT-Gi0/0.7 class OUT-VOICE ...

jbaros by Level 1
  • 963 Views
  • 1 replies
  • 0 Helpful votes

Hi Experts. I have faced issue with module 3 before some days, below logs is generated on device and its looks like software but unable to isolate issue because kernal dump file is corrupt.. Need your help to find  RCA. LC/0/1/CPU0:Apr 7 23:20:54.827...

Vivek by Level 1
  • 1814 Views
  • 2 replies
  • 0 Helpful votes

How much routing capabilities do I have with lanbase?  Meaning can I use floating static routes? ip route x.x.x.x x.x.x.x 10.0.0.1ip route x.x.x.x x.x.x.x 10.0.0.2 200   ---- Will this work   I have tested and it doesn't seem like that will work.   H...

Hello, We have roughly 50 1941 Cell routers in our environment. For the past 3 months ,once a month, they have all went down at the same time, and came back up at the same time. The outage was roughly 1 minute long.  In each router, they all say the ...

Chop87 by Level 1
  • 521 Views
  • 3 replies
  • 0 Helpful votes

HelloI have a wan modem connected to a Cisco RV130 and enabled pptp VPN.I can establish a secure connection though the WAN modem into the device via pptp.  I can ping devices on the LAN side of the RV130.  I can open local web pages for the configura...

Dougm by Level 1
  • 745 Views
  • 3 replies
  • 0 Helpful votes

Hi, I have 2 ISP's. Cisco 3825 router and Cisco 3750 as core switch.  WAN SIDEHave terminated both ISP's in Cisco 3750 on different Vlans (101 and 201). From there made a trunk of both vlans and connected it on Cisco 3825 by making sub-interfaces.  L...

Mubeen by Level 1
  • 1084 Views
  • 7 replies
  • 0 Helpful votes

AnyConnect is working but I can't access the web server but ping works.  Attached is the full configuration.  I had to remove the nat to get it to work.((( no nat (inside,outside) source static 192.168.172.0_24 192.168.172.0_24 destination static )))...

anyconnect_172_crop.png anyconnect_wireshark_http_80.jpg wireshark_capture_telnet_80_crop.jpg

hi friens i have a question there is s imple topology PE1 <------->P<------->PE2on both PEs i configured vrf  vrf_alet us  use PE2 as an exaplPE2(config-vrf)#do show ip rou vrf vrf_aGateway of last resort is not set33.0.0.0/32 is subnetted, 1 subnets...

Hi everyone. I have own public ips and ASN and configuration BGP everything is ok. I can go to internet with my own IP. But when I want nat my internal subnet to my public ip and go to internet or do static nat not working. I want configuration nat o...

Hi AllWe currently have a WIC-1T serial interface in our old router with DB60 cable, this is running at 1.544Mbit so I am guessing it is a T1, we want to replace with a 4331, however this interface is not supported.It is for data only, for this do we...