We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
hi guysI upgraded my SG500 switch firmware to 1.3.0.59, since there is a new functionality DHCP server v.4well I must say I came accross the issue I cannot solve. DHCP server assign dynamic address - no hassles. troubles start with static IP hosts.I ...
Hello. I've managed to collect information piece by piece on forums, MIBs, boards etc and make work reading status information from this switch into some managing software.Now I'm stuck on setting vlans or port:Common OIDs "vtpVlanEdit" section (1.3...
Hi Community We have 2 units of "SG550XG-48T 48-Port 10GBase-T Stackable Managed Switch" in native stacking mode.We have to reboot the whole stack, but we want only reboot unit 1 and then after i few minutes unit 2. This because we have LACP enabled ...
Hi,I'm working with AV company dealing with Crestron and Dante audio combo . I normally enable edgeport on SG300 and we never had any issues with Dante devices after reboot or unplugging/plugging devices to the switch. Dante controller shows all devi...
We have a few several-years-old Cisco Series 300 series switches, 100Mb Ethernet PoE, that we are looking at replacing. One 48-port switch and four 24-port switches. What is the difference between the SG300 and the SG350 series -- besides price?? I'm...
Resolved! 3560-CX strange/incorrect temp reading
We recently got a 3560CX (WS-C3560CX-12PC-S). Where it is currently situated seems extremely hot. So to check the temp we logged onto the switch but received the following which does not make sense: According to this we would not get an error until...
Resolved! SG300-28 without fan - add fan and temp
HiI have a switch sg300-28 without fan and not show temp. I see that in motherboard is point to solder plug for fans and I test and it give on one pin 12V and on second about 3.3V.Is any chance to solder plug and connect fan. It works ok but in GUI n...
Good morning, according to the CLI manual, release 1.4, page 980 ff. there is a "show environment" command similar to regular Cisco switches. When typing this command in the CLI there's a "Unrecognized command" error message. Is there any way to get ...
Experts,Appreciate your quick assistance here.My Customer is working on optimizing the environmental conditions at all his Data Center locations (Currently they are in the range 68F to 74F at their locations and they want to increase the temp to 76F)...
Hello,I am trying to assign a public IP address to my PDU which acquires an IP address automatically via DHCP so i can manage remotely. I have tried this with the switch mode in Layer 2 and didn't get it to work so now I'm trying in Layer 3. I have c...
hi guys, I`d like to know if it`s possible to setup an authentication for the WebGUI Access via TACACS and give explicit customized permissions for configuring the switch on an ACS? what I also cannot find in the WebGUI configuration, is the conf...
Resolved! SGE2010 change VLAN1 IP address
Hi, it is my first post, sorry but my english is very bad!!! I want to know how am i do to change the Vlan1`s IP address because the actual ip will be used in another vlan. Actually i haver 10 vlans in L3 mode (routing) implemented in it.I hope you u...
I'm adding an SG500-52P switch to my network and have set it to L3mode. My network has an MS320 Meraki LAN switch that this L3 SG500 switch is uplinked to. Also, my network has 8 other SG500 switches in L2 mode uplinked to the Meraki MS320 switch. On...
Please help for my thesis I've created VLAN'S and which is i created DHCP POOL FOR EVERY VLANS IT IS WORKING BUT MY ISP ROUTE HAS AN IP ADDRESS OF 192.168.1.1 THEN MY CISCO ROUTER IP ADDRESS IS 192.168.2.1 ALSO I MADE DEFAULT ROUTE 0.0.0.0 0.0.0.0 19...
Hello, I feel stuck trying to configure our SG350-28P. My SG350-28P is connected to our datacenter 3560X via fiber. I am able to remotely access the switch via SSH and HTTPS so I know connectivity back to the primary switch is good. However, I cann...
