Switches - Small Business - Page 45

Looking for support docs and videos? Check here

We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...

Helpful support links - Updated September 2023 w/ Catalyst 1200 - 1300

(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...

Can I easily move the configuration from a SF300-24P to CBS250-48P?

I have an old Cisco SF300-24P switch which is end of life (and out of ports).I purchased a new CBS250-48P and I'm wondering if I can just load the configuration over?

Connection issue - ARP reply being blocked?

I have a computer connected to a Cisco SF300-24P switch (on an access port for VLAN 88).I have a server connected to a TP-Link switch (on an access port for VLAN 88)The Cisco switch is connected to a TP-Link switch with a trunk port allowing native V...

SG500 - Maximum TCAM Entries?

Does anyone know the maximum TCAM entries allowed for IPv4 and IPv6 Routing?

Resolved! after config restore: config works BUT cannot login any longer

I restored a config to a CBS250-8T-D switch from a backup file.The restored config works,HOWEVER, i canot login any longer: "invalid user or password"When i reboot the switch it goes back to the config prior to the restore.And the login is working ag...

Windows Server 2016, 10Gb NIC & Cisco SG350X = less than 1Gb Lan speed

So we seem to have a bit of mystery over here.We have several rendernodes attached to a Cisco SG350X-24, which in turn is attached to an SX350X-12 through the 10Gb ports. Attached to that SX350 are also 2 data serverss (Windows Server 2016 OS) throug...

Does cbs350 support port forwarding and NAT

Kindly advise which cisco 8 port switch can support port forwarding and NAT to give public access from Internet to secure server in office behind switch

Cisco small bussiness switches SKU CCW

Hello with everyone, A good day, I don't find the sku in the CCW tool. I don't find the ordering guide as well. Thanks for your recomendations. Wilson

CBS250 ACL - wildcard, whats the difference

Hello,actually I think I have an understanding problem with ACL on the CBS250 series.I use a DHCP Server with IP: 192.168.100.65/27 When I set this input rule:permit udp any any 192.168.100.65 0.0.0.0 67-68 ace-priority 1The client cannot recieve the...

Resolved! Difference between CBS250-8T-D and CBS250-8T-E-2G?

Hello, so far I use the CISCO switches CBS250-8T-E-2G in my network and would like to add another switch.Here I came across the model CBS250-8T-D.From the datasheet I can see these differences:- CBS250-8T-D has a smaller power consumption- CBS250-8T-...

SG250X-24P Support

Hi,I am having issues with two separate SG250X-24P units. Last week they suddenly stopped working and supporting the network. The main wifi router works fine and can be used with WiFi and Ethernet directly. The port used to support our WiFi repeaters...

Adding SG550X to an existing stack

We have a current stack of five (5) SG550X-48P switches, and are adding a new SG550X-48P switch to the stack. What is the correct procedure to add this switch to the stack? And, can we add this switch to the stack without rebooting the entire stack...

SGE2010p Firmware

Hello, i know those switch are old, but im looking for the latest firmware available for those switch. i have a few in production and as much as id like to upgrade them, they are working just fine for whats needed. Cisco Support as been less than hel...

Need technical suggestion

Hello Team, Can you please confirm if cat6A cable supports with SG300 52 port switch ? Thank you in advance.Ranjan Mohanty

Resolved! CBS350-12XS inaccessible after Firmware update

I had two CBS350-12XS stacked when I performed a firmware update. After rebooting I was unable to get to the WebGUI or through the CLI console port. They will reboot when the reset switch is pressed and seem to recognize the long press to reset the f...

Resolved! SG300-28MP power inline or shutdown?

I have a customer with a SG300-28MP and they want to be able to shut down or enable wi-fi when ever. Since I have AMX touch panels mounted in various locations I want to give them the ability via the touch screens to enable or disable or even select...

Switches - Small Business

Forum Posts

Looking for support docs and videos? Check here

Helpful support links - Updated September 2023 w/ Catalyst 1200 - 1300

Can I easily move the configuration from a SF300-24P to CBS250-48P?

Connection issue - ARP reply being blocked?

SG500 - Maximum TCAM Entries?

Resolved! after config restore: config works BUT cannot login any longer

Windows Server 2016, 10Gb NIC & Cisco SG350X = less than 1Gb Lan speed

Does cbs350 support port forwarding and NAT

Cisco small bussiness switches SKU CCW

CBS250 ACL - wildcard, whats the difference

Resolved! Difference between CBS250-8T-D and CBS250-8T-E-2G?

SG250X-24P Support

Adding SG550X to an existing stack

SGE2010p Firmware

Need technical suggestion

Resolved! CBS350-12XS inaccessible after Firmware update

Resolved! SG300-28MP power inline or shutdown?

Congratulations to the Event Top Contributors Class of 2024!

Cisco + Splunk: It's a new day for your data.

A new chapter of the Spotlight Award begins!

Join us in Celebrating the New Year and the Nov.-Jan. Winners!

Announcing Resources That Guide You to Success

Cisco Business Product Family

Cisco Switching Product Family

Difficult to find MIB CPU utilisation Switch - model CBS250-8T-D

CBS350 renew wildcard SSL certificate

sg500 DHCP pool limit

Which series of Cisco switch 24 port PoE+ for Arbua AP 635

is it possible to restore sg300-28 config on a sg300-28PP Switch