Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Can inter Vlan routing done in CBS 350 or what kind of vlan is possible ?
Hi Team, Please confirm whether Cisco Switches comes with built in surge protection device. Thanks, Akshatha
Hello I need to recover the enable password on a 4510R with dual supervisors V, what is the proper precedure for doing this?
Hello, I feel like I am going crazy.I have a PLC that is on VLAN 10, and production clients and label printers that are on VLAN 100.Vlan 10 IP range is 172.18.XX.0 rangeVLAN 100 is on 10.68.XX.0 range.C2960 switchGi1/0/38 is connected to a smaller "d...
Resolved! port-channel / suspended interface
I have to 2 X Gbics connected to MX 450 appliance and my desire is create a port-channel from the MX to cisco switch. upon completing the configuration i get UP/DOWN with interface status suspended. sho run int GigabitEthernet4/0/36interface GigabitE...
Resolved! Monitor ISP Links
Hi Team,How can we monitor the ISP links if any link goes down? Is there a tool available? What are the best practices to monitor it?
Resolved! NAT troubleshooting
Can I get some help understanding why my lab scenario dint work: I have two subnets (A) 10.0.0.0/28 and (B) 10.0.0.16/28, I wanted to set up NAT but my idea was to allow anything from (C) 10.0.0.0/24, in case I added a new subnet, anything that would...
Resolved! iPerf on Catalyst 9300
Hello everyone, I am using iPerf on a Catalyst 9300 switch.I managed to configure everything, but my question is: can I use the SVI as the guest-ipaddress of iPerf or a separate IP address is always needed for the machine?I tried this configuration b...
Hi, now I am practicing the network.And redistributing, It is difficult for me.I don't know how do I redistribute between static routing and RIPv2? I attached the topology,, please let me know. I setted .. R1 #int f0/0#ip add 172.100.100.1 255.255.25...
Hi to all Sifu, On the server side: They are doing NIC teamingOn the network side: We are doing VPCAs in the pic above, that is how the endpoint is connected to the leaf switch. When I run the command 'show endpoint ip 10.201.128.95' the result is as...
Resolved! SX350X-24F - restart in a loop
Hello,We have two Cisco SX350X-24F switches in a stack. They have worked for 2 months without any problems. Last night one of them suddenly started rebooting over and over again. Access was only possible through the console cable. Restoring the facto...
I wonder when is IOSXE Devices going to be available to Lab VXLAN. Recently embracing new network designs such as Spine Leaf, noticed can't lab because the gaps on IOS. I think will be awesome to have support to simulate VXLAN. Considering is the fut...
Resolved! ROAS and VLANs
Going to try to keep this simple. In order for ROAS to function, the VLANs themselves don't need to be configured on the router right? Just the sub interfaces? I only ask as I have setup subinterface gi0/0/0.10 for tag 10 and subinterface gi0/0/0.20 ...
hi on one end i have WS-C3850-48P and on the other end i have WS-C2960X-48FPD-L. Daily for sometime i receive alert for output error on particular interfaces which are part of portchannel of WS-C3850-48P. Daily i face this issue during business hour...
What's up with making DHCP reservations based on MAC addresses? I'm using the client-identifier command after setting the host ip in the dhcp pool, and prepending an 01 to the MAC address I see for the interface of a machine (say a Linux one). I noti...
