Hi Guys I am working on a lab at home and have got all my switching and firewall stuff working. I am trying to setup a simple connection from my router to the ISP router. Both are 2611xm routers. The protocol just does not come up. I have labbed just...
I'm the new IT guy in this company. Previously, a WS-C2924M-XL switch in our main office had been upgraded and the old switch was installed in our branch office 300 miles away. This switch was originally configured with an ip address, netmask, and ...
In above diagram I am trying to configure RSPAN on Cisco 6509 Switch. As it is a intermediate switch, I am not sure how do I configure it. Can anyone please assist me in configuring the same.
I'm looking to setup a dual ISP setup on a 3750 Layer 3 switch. One of the ISPs terminates directly into the 3750 on a VLAN and the other ISP will be behind two Routers/HSRP and terminates into an ASA on the other side. I'm looking for an option th...
Hello, I am just getting my feet wet with Cisco equipment and have setup a lab with two 3560 switches and a 2600 router. I am trying to get internet connectivity established on the router, but do not seem to be having any luck. I can pull an IP a...
We recently had a hard shutdown of our 6509 core due to a power outage.When it came back up, the supervisor came up fine and one of the line cards did, however, 3 line cards failed to come up. There seemed to be a power issue with a red status. They ...
Hello Experts,I want to have a network monitoring tool to log and report followings to me:1- Show Real-Time internet bandwidth usage of every user individually, showing which user is killing/Eating the bandwidth2- Log and Report users internet traffi...
Unable to successfully communication between interfaces on ASA 5525X. Have configured same-security-traffic permit inter-interface.Unable to use static command to translate?
Hi, I am trying to accomplish a routing task and need a little guidance, I have Cisco 887 ADSL Router that is our network's default gateway. There are several NAT entries for different servers and ports etc. The issue i have is that the ADSL conne...
Hi all,This is my 1st post so please bare with me if I missed any common forum decorum.project:I need to allow 3 vm's multicast packet propagation within a server cluster where network latency is low enough to ensure that most multicast messages reac...
Hi I have done natting on a router before and that seemed quite straight-forward. I am just looking at some router config done by someone else but Im confused why they have used route maps as part of the NAT configs. I would usually create an access ...
Hi everyone,Please help me with the following queries.Suppose we have only one vlan (e.g vlan 10) vlan 10 consist of 100 hosts on multiple switches.I have created four vtp domain,each domain consist of 25 host and one server switch.How many broadcast...
I have several routers using VRF-lite to separate the layer 3 routing tables between two type of services. Each of these routers runs EIGRP in both VRF instances. The logical topology is the same as the physical. When I run "show ip eigrp vrf VOICE n...
Hi all,The network topology is illustrated below:WAN ------ Router ------ L3 Switch ------ Client PIM-SD are configured on both L3 Switch and Router. The Client is going to join a multicast group, for example 239.42.1.1. This join message is received...
Hey all,We recently implemented root guard on our two core devices, on both ports that point to our distribution layer. This broke the link from our secondary router to the distribution layer, which remains in a BKN state due to the root BPDU that p...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 04-24-2025 03:01 AM | ||
| 04-23-2025 06:26 AM | ||
| 04-23-2025 06:18 AM | ||
| 04-19-2025 09:40 AM | ||
| 04-15-2025 04:52 AM |
| User | Count |
|---|---|
| 7 | |
| 7 | |
| 6 | |
| 5 | |
| 3 |
