Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Hi every body!i am just curious if a switch has f0/1 as trunk, and i use the command " show mac address-table", how it will appear in the output.Thanks and have a nice weekend !
Hi,I am a little confused with SVIs.This is the MAC address table and ARP on a device which is connected to a neighbor: Destination Address Address Type VLAN Destination Port------------------- ------------ ---- --------------------aaaa.bbbb.ccc ...
Hello guys,I want to know how switches that are stacked virtually would operate. Would you require separate management IP’s for them, are the configurations synch across. Also, can I run the stack-wise config on interfaces that are bundled together u...
Resolved! VPCs Peer is Dead
I have a pair of Nexus 5596 switches that are configured to be VPC peers. One of the switches is “dead” and I cannot get the active VPC member to restore the configured VPCs to resume operations.The current config of the live switch (VPC peer) is:VP...
Hello.Device is Cat 9300 switch stack (x4). OS is 17.03.03--------Loading os/cat9k_iosxe.17.06.04.SPA.bin from 172.16.1.5 (via Vlan5): !!O!!!!!!O!!!!!!!!!!!!.O!OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO!!!!!!!O!!!!!!!!...
Resolved! Cat 2960X-- "boot system" syntax...
I am concerned that the syntax for #boot system is incorrect, which may lead to a locked out failed switch. May you please confirm that this is correct?2960X(config)#boot system flash:c2960x-universalk9-mz.152-7.E7.bin2960X#sh bootBOOT path-list : fl...
Resolved! Dhcp failed apipa being used
this is my topology and I am trying to pool my dhcp from router 2 to sw1 and 2. But for some reason my dhcp pool won't work.I have trunked bithe switches and also they are set to sw mode acc.
Hello,I am getting an error on a C9200 with the following:27246010: Mar 3 12:19:31.429 EST: SISF_DB_IOS_ERR: sisf add or update record error (Not enough space)27246011: Mar 3 12:19:31.430 EST: SISF_DB_IOS_ERR: Unable to find IP record for key XXXX::X...
We have 2 NEXUS Switches in VPC and a port-channel with 2 10G members link (one member in every switch), all this in SITE A. On the other hand, we have a SITE B with the same hardware configuration. The port-channel between SITES carries only a 802...
I was planning to upgrade the Nexus 9504 from 7.0(3)I7(4) to 9.3.X However, referring to the Nexus 2348TQ datasheet, I noticed that in the minimum software it lists NX-OS 9.2.1, but not the 9.3.X. I would like to know if anyone's setup runs the 9.3.X...
Resolved! LLQ for 9200 switch and isr 4331
Hi. I have a task to configure traffic prioritization, since the topic is very big, I don't really understand which solution in combination would be the best for me qos, llq, maybe something else... Please help.1. I have a channel from an ISP of 300 ...
Hi AllWe just purchased 2 catalyst 9200L switches. My laptop connects through the console port but only giving gibberish. I have confirmed the connection settings. Tried a couple different speeds but still the same result. I replaced the serial cable...
Resolved! Delete file with space character
Hi,I want to delete some files from router flash: But filename have space character... Exemple: flash:New folderDoes someone have a idea what I can do? Thank you for your help
Hi,Can anyone please help me on how to console into a Cisco 2900 xl series switch? I used the same console cable which i use to connect my routers but when i try to connect the 2 swicthes through hyper terminal it doesn't display anything.I used the ...
I have a standalone switch that has the ip 192.168.172.230. I tried to configure same ip as the default-gateway for that switch, because it is an standalone. I just though i could point on the same swtich as default-gateway. It turned out, that it is...
